Containing less than 8 percent by weight of nickel
Other bars and rods of stainless steel; angles, shapes and sections of stainless steel: > Bars and rods, not further worked than cold-formed or cold-finished > Other: > Of a circular cross-section: > With a maximum circular cross-sectional dimension of less than 18 mm: > Containing less than 8 percent by weight of nickel
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7222.20.00.41
443 Stainless Cold Bar 12.8mm Circular
Automotive 443 stainless cold bar, 12.8 mm dia., <8% Ni for trim. HTS 7222.20.0041 stainless rod. ESR refined.
Cold-Drawn 304 Stainless Tie Bar 16.9mm
16.9 mm 304 stainless tie bar stock, cold-drawn <8% Ni for concrete forms. HTS 7222.20.0041. General corrosion resistance.
439LF Stainless Steel Cold Rod 17mm Diameter
Low-ferrite 439LF stainless cold rod, 17 mm round, <8% Ni for exhaust manifolds. HTS 7222.20.0041 for cold-finished stainless bars this size. Optimized weldability.
301 Full Hard Cold-Rolled Bar 10.5mm
Full hard condition 301 stainless bar, 10.5 mm dia., cold-rolled <8% Ni for springs. HTS 7222.20.0041 cold-finished stainless rod. High tensile strength.
Cold-Finished 304 Stainless Steel Round Bar 10mm
A cold-finished round bar of 304 stainless steel with a 10 mm diameter and less than 8% nickel content, not further worked beyond cold-forming. This falls under HTS 7222.20.0041 due to its circular cross-section under 18 mm, stainless steel composition, and minimal nickel. Commonly used in precision mechanical applications requiring corrosion resistance.
420 Stainless Cold-Finished Dowel Rod 14mm
14 mm 420 martensitic stainless dowel rod, cold-finished <8% Ni for hardened pins. HTS 7222.20.0041 small stainless bar. Corrosion resistant when hardened.
316L Stainless Steel Cold-Drawn Rod 12mm Diameter
Cold-drawn 316L stainless steel rod featuring a 12 mm circular cross-section and under 8% nickel by weight, suitable for marine environments. Classified in HTS 7222.20.0041 for its small diameter stainless steel bars not further worked than cold-finished. Ideal for shafts and fasteners in corrosive settings.
Cold-Formed 430 Stainless Steel Bar 14.5mm Round
A 14.5 mm diameter round bar of 430 stainless steel, cold-formed with less than 8% nickel, used in automotive trim and hardware. HTS 7222.20.0041 applies to these small-section, cold-finished stainless bars without additional processing. Offers good formability and moderate corrosion resistance.
Precision Ground 409 Stainless Rod 8mm Diameter
Cold-finished 409 stainless steel rod with 8 mm round cross-section and <8% nickel, designed for exhaust system components. Falls under HTS 7222.20.0041 as cold-formed stainless bars not exceeding 18 mm diameter. Provides heat resistance for automotive applications.
Cold-Rolled 301 Stainless Steel Shaft Blank 15mm
15 mm diameter cold-rolled 301 stainless steel bar with under 8% nickel, used as shaft blanks in machinery. HTS 7222.20.0041 covers these small, cold-finished circular stainless rods. Known for high strength and ductility in spring applications.
17-4 PH Stainless Steel Cold-Finished Bar 11mm
Cold-finished 17-4 PH precipitation-hardening stainless bar, 11 mm round with <8% nickel, for aerospace fasteners. Classified under HTS 7222.20.0041 for small-diameter cold-formed stainless steel. Offers superior strength after heat treatment.
Ferritic 439 Stainless Round Rod 9mm Diameter
9 mm cold-finished ferritic 439 stainless steel rod with low nickel content (<8%), used in appliances and tubing. HTS 7222.20.0041 for circular cross-section under 18 mm, cold-formed stainless bars. Excellent for welded fabrications.
Duplex 2205 Stainless Cold Bar 16mm Round
Cold-drawn duplex 2205 stainless steel bar, 16 mm diameter with <8% nickel, for offshore platforms. Under HTS 7222.20.0041 as small cold-finished circular stainless rod. Combines austenitic/ferritic properties for high corrosion resistance.
Martensitic 410 Stainless Rod 13mm Cold-Finished
13 mm cold-finished martensitic 410 stainless rod, <8% Ni, for pump shafts and valves. HTS 7222.20.0041 specifies these low-Ni, small-diameter stainless bars cold-formed only. Heat-treatable for hardness.
Cold-Formed 304L Stainless Pin Stock 7mm
7 mm diameter 304L stainless pin stock bar, cold-formed with <8% nickel for dowel pins. Classified HTS 7222.20.0041 for precision cold-finished stainless circles under 18 mm. Low carbon for weldability.