Low Chromium 430-Modified Cold-Rolled Steel Coil
A modified 430 series cold-rolled stainless coil with 14.5% chromium, 0.8 mm thick and 1000 mm wide, for appliance panels. It is a flat-rolled stainless product, not further worked than cold-rolled, and its thickness of 0.8 mm places it within the 0.5 mm to 1 mm range of tariff item 7219.34.00.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
PGA flags (1)Show detailsHide detailsGACSteelRequired
- GAC
Steel · Required
Global Affairs Canada: GAC Steel (Specialty Steel) requires review / declaration data. CBSA's Single Window matching criteria match this classification number (Within Range 7218000000–7224999999).
CBSA Single Window matching criteria, unknown
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the thickness is greater than 1 mm
Thicker cold-rolled stainless products are classified in the next subheading.
If the width is less than 600 mm
Narrower stainless flat products fall under heading 7220.
If the coil is stamped into finished appliance panels
Household articles of stainless steel are classified in Chapter 73.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Even with 14.5% chromium (below 15%), the steel qualifies as stainless since it exceeds 10.5%
• The coil must be in coils and not further worked than cold-rolled; any additional coating or polishing would change classification
• Provide a certificate of analysis to confirm the chromium content for CBSA
Related Products under Tariff item 7219.34.00
0.9mm Thick Low-Cr Cold-Rolled Stainless Master Coil
A master coil of cold-rolled stainless steel with 12% chromium content, measuring 0.9 mm in nominal thickness and 1,500 mm in width, intended for slitting into narrower coils. This product is classified under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the 0.5-1 mm thickness range.
11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
A cold-rolled stainless steel coil with 11% chromium content, measuring 0.7 mm in thickness and 750 mm in width, supplied in coils for stamping automotive exterior trim. This product falls under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the specified thickness range.
17-4PH Precipitation Hardening Stainless Coil 0.65mm
A 17-4PH precipitation hardening stainless steel coil, cold-rolled to 0.65 mm thickness, in a wide format. It is a flat-rolled stainless product, not further worked than cold-rolled, and falls under tariff item 7219.34.00 because its thickness is 0.65 mm, within the 0.5 mm to 1 mm range.
17-4PH Precipitation Hardening Stainless Coil 0.7mm
A cold-rolled coil of 17-4PH precipitation hardening stainless steel, containing approximately 4% copper, 15-17.5% chromium, and 3-5% nickel. It has a thickness of 0.7 mm and is supplied in wide coils. This product falls under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the 0.5-1 mm thickness band.
17-4PH Precipitation Hardening Stainless Steel Coil
Cold-reduced coil of 17-4PH stainless steel, 0.7 mm thick, 1,000 mm wide, with 3.0% molybdenum and 4.0% nickel. This precipitation-hardening stainless steel is a flat-rolled product not further worked than cold-rolled, within the specified thickness range.
304 Cold-Rolled Stainless Steel for Sink Manufacturing 0.8 mm
Commercial 304 stainless steel cold-rolled sheet, 0.8 mm thick and 610 mm or more wide, supplied in mill finish for kitchen sink fabrication. It is not further worked beyond cold reduction, meeting the tariff item's thickness range of 0.5 mm to 1 mm.