17-4PH Precipitation Hardening Stainless Coil 0.65mm
A 17-4PH precipitation hardening stainless steel coil, cold-rolled to 0.65 mm thickness, in a wide format. It is a flat-rolled stainless product, not further worked than cold-rolled, and falls under tariff item 7219.34.00 because its thickness is 0.65 mm, within the 0.5 mm to 1 mm range.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the thickness is greater than 1 mm
Thicker cold-rolled stainless products are classified in a different subheading.
If the width is less than 600 mm
Narrower stainless flat products fall under heading 7220.
If the product is in bar or rod form
Other bars and rods of stainless steel are classified in heading 7222.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• 17-4PH is a precipitation-hardening stainless steel with sufficient chromium (about 15-17.5%) to qualify as stainless
• The coil must be in coils and not further worked than cold-rolled; any aging or hardening treatment after cold-rolling could affect classification
• Provide detailed alloy composition documentation for CBSA
Related Products under Tariff item 7219.34.00
0.9mm Thick Low-Cr Cold-Rolled Stainless Master Coil
A master coil of cold-rolled stainless steel with 12% chromium content, measuring 0.9 mm in nominal thickness and 1,500 mm in width, intended for slitting into narrower coils. This product is classified under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the 0.5-1 mm thickness range.
11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
A cold-rolled stainless steel coil with 11% chromium content, measuring 0.7 mm in thickness and 750 mm in width, supplied in coils for stamping automotive exterior trim. This product falls under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the specified thickness range.
17-4PH Precipitation Hardening Stainless Coil 0.7mm
A cold-rolled coil of 17-4PH precipitation hardening stainless steel, containing approximately 4% copper, 15-17.5% chromium, and 3-5% nickel. It has a thickness of 0.7 mm and is supplied in wide coils. This product falls under 7219.34.00 as flat-rolled stainless steel, not further worked than cold-rolled, within the 0.5-1 mm thickness band.
17-4PH Precipitation Hardening Stainless Steel Coil
Cold-reduced coil of 17-4PH stainless steel, 0.7 mm thick, 1,000 mm wide, with 3.0% molybdenum and 4.0% nickel. This precipitation-hardening stainless steel is a flat-rolled product not further worked than cold-rolled, within the specified thickness range.
304 Cold-Rolled Stainless Steel for Sink Manufacturing 0.8 mm
Commercial 304 stainless steel cold-rolled sheet, 0.8 mm thick and 610 mm or more wide, supplied in mill finish for kitchen sink fabrication. It is not further worked beyond cold reduction, meeting the tariff item's thickness range of 0.5 mm to 1 mm.
310S Cold-Rolled Stainless Steel Coil 0.75mm Heat-Resistant
A high-temperature 310S stainless steel coil, cold-rolled to 0.75 mm thickness and 650 mm width, for furnace parts. It is a flat-rolled stainless product, not further worked than cold-rolled, and its thickness of 0.75 mm places it within the 0.5 mm to 1 mm band of tariff item 7219.34.00.