Of a thickness of 0.5 mm or more but not exceeding 1 mm
Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated. > In coils, not further worked than cold-rolled (cold-reduced): > Of a thickness of 0.5 mm or more but not exceeding 1 mm
Duty Rate (from China)
Subheadings
Products classified under Tariff item 7209.17.00
Advanced AHSS 1180 Steel Annealed Coil
Third-generation advanced high-strength steel (AHSS) 1180 MPa annealed coil, cold-rolled to 0.6 mm thickness and 650 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 because its thickness is between 0.5 mm and 1 mm. Used in high-performance automotive safety components requiring exceptional strength and formability.
Advanced CAHSS Complex Phase Steel Coil
Complex-phase advanced high-strength steel (CAHSS) coil, cold-rolled and annealed to 0.95 mm thickness. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Balances strength and formability for truck panels and structural automotive applications.
Advanced High-Strength DP980 Steel Coil
Cold-rolled dual-phase (DP) 980 MPa high-strength steel coil, annealed, with thickness between 0.5 mm and 1 mm and width exceeding 600 mm. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and is classified under tariff item 7209.17.00. Used in automotive structural components requiring high strength and energy absorption.
Advanced Martensitic MS980 Cold-Rolled Steel Coil
Annealed martensitic MS980 steel coil, cold-rolled to 0.8 mm thickness and 800 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 due to its thickness range. Designed for lightweight vehicle chassis and structural reinforcements requiring ultra-high strength.
Advanced TWIP Steel High-Strength Coil
Twinning-induced plasticity (TWIP) advanced steel coil, cold-rolled to 0.55 mm thickness and annealed. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Offers high ductility for complex forming applications in vehicles, such as body panels and crash structures.
Annealed High-Strength Steel Coil for Appliance Housings
Cold-rolled non-alloy steel coil, 0.9 mm thick by 1000 mm wide, high-strength grade with 355 MPa yield after annealing. This flat-rolled product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 due to its thickness range. Used for appliance housings requiring strength and formability.
Annealed High-Strength Steel Coil for Furniture Frames
Cold-reduced high-strength steel coil, 0.55 mm x 650 mm, annealed, suitable for heavy-duty furniture reinforcement. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Provides structural support in commercial and residential furniture frames.
Automotive Grade Annealed HSLA Steel Coil
High-strength low-alloy (HSLA) steel coil, cold-rolled to 0.75 mm thickness and 1200 mm width, annealed, with 300 MPa minimum yield. This flat-rolled product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00. Used in automotive structural components requiring high strength and good formability.
Automotive High-Strength Cold-Reduced Steel for Door Frames
Automotive high-strength cold-reduced steel coil, 0.6 mm thick and 1,500 mm wide, with a minimum yield strength of 275 MPa, used for car door inner frames. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and falls under 7209.17.00 due to its thickness of 0.5-1 mm.
Cold-Rolled Annealed Steel Coil 0.65mm for Lockers
Cold-rolled annealed non-alloy steel coil, 0.65 mm thick and 600+ mm wide, without cladding or coatings. This product is not further worked beyond cold-rolling, meeting the tariff item's specification for flat-rolled products in coils of this thickness range.
Cold-Rolled Automotive Grade 1 Steel Coil 0.78mm
Automotive-grade non-alloy cold-rolled steel coil, 0.78 mm thick and over 600 mm wide, uncoated and not further worked. This product fits the tariff item's definition of flat-rolled products in coils, cold-reduced, within the specified thickness range.
Cold-Rolled Commercial Quality Steel Coil 1.0mm for HVAC Ducts
Commercial quality non-alloy steel, cold-rolled in coils to a maximum thickness of 1 mm and over 600 mm wide, without plating or further working. This product matches the tariff item's scope for uncoated cold-reduced flat products used in HVAC applications.
Cold-Rolled Deep Drawing Steel Coil 0.75mm for Battery Casings
Deep drawing quality cold-rolled non-alloy steel coil, 0.75 mm thick and over 600 mm wide, not clad or coated. This product is classified under the tariff item as a cold-reduced coil within the specified thickness range, without further processing.
Cold-Rolled Drawing Quality Steel Coil 0.6mm for Metal Containers
Drawing quality non-alloy steel coil, cold-rolled to 0.6 mm thickness with width over 600 mm, not further processed beyond cold-reduction. This product fits the tariff item's description for cold-reduced coils in the 0.5-1 mm thickness range.
Cold-Rolled EDD Steel Coil 0.95mm for White Goods
Extra deep drawing (EDD) non-alloy steel cold-rolled coil at 0.95 mm thickness, over 600 mm wide, uncoated. This product is classified under the tariff item as a cold-reduced, non-further-worked coil used in white goods manufacturing.
Cold-Rolled General Purpose Steel Coil 0.58mm
General purpose non-alloy steel cold-rolled coil at 0.58 mm thickness, over 600 mm wide, with no further treatments. This product matches the tariff item's scope for uncoated cold-reduced coils, suitable for stamping applications.
Cold-Rolled High Formability Steel Coil 0.92mm for Panels
High formability non-alloy cold-rolled steel coil, 0.92 mm thick, with coil width exceeding 600 mm, not clad or plated. This product is classified under the tariff item for cold-reduced, not further worked products used in architectural panels.
Cold-Rolled High-Strength Steel for Furniture Frames
Cold-rolled high-strength steel coil, 0.85 mm thick and 700 mm wide, with a 345 MPa yield strength, used for commercial office furniture structural frames. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and classified under 7209.17.00 because its thickness is within 0.5-1 mm.
Cold-Rolled High-Strength Steel for Solar Panel Frames
Cold-rolled high-strength steel coil, 0.75 mm thick and 800 mm wide, with a 355 MPa yield strength, used for solar panel mounting frames. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and falls under 7209.17.00 due to its thickness of 0.5-1 mm.
Cold-Rolled HRPO Alternative Steel Coil 0.62mm
Cold-rolled non-alloy steel coil equivalent to HRPO but uncoated, 0.62 mm thick and over 600 mm wide, not further worked. This product is classed under the tariff item for cold-reduced coils without plating, for general fabrication.
Cold-Rolled IF Steel Coil 0.72mm for Radiators
Interstitial-free (IF) non-alloy steel cold-rolled to 0.72 mm, in coil form over 600 mm wide, with no cladding or coating. This product falls under the tariff item as a cold-reduced product without further working, used in heat exchanger components.
Cold-Rolled Low Carbon Steel Coil 0.9mm for Furniture Frames
Low-carbon non-alloy steel flat-rolled in coils, cold-rolled to 0.9 mm thick and over 600 mm wide, free of plating, cladding, or additional surface treatments. This product is classified under the tariff item for uncoated, cold-reduced coils.
Cold-Rolled Mild Steel Coil 0.7mm for Appliance Housings
Cold-reduced mild steel coil with 0.7 mm thickness, width exceeding 600 mm, in coil form without cladding, plating, or further working. This product is classified under the tariff item for non-alloy steel cold-rolled products in the 0.5-1 mm range.
Cold-Rolled Nonalloy Steel Coil 0.8mm Thick for Automotive Panels
Flat-rolled non-alloy steel coil, cold-rolled to a thickness of 0.8 mm and width over 600 mm, not clad, plated, or coated, and not further worked beyond cold-rolling. This product falls under the tariff item due to its specific thickness and form.
Cold-Rolled Skin-Pass Steel Coil 0.85mm for Roofing
Skin-passed cold-rolled non-alloy steel coil, 0.85 mm thick, width over 600 mm, not plated or further worked beyond cold-reduction. This product matches the tariff item for uncoated coil in the specified thickness range, for pre-painted roofing applications.
Cold-Rolled Structural Steel Coil 0.55mm for Shelving
Non-alloy structural grade steel coil cold-rolled to 0.55 mm, over 600 mm wide, with no plating or additional treatments. This product is designated under the tariff item for uncoated, cold-reduced thickness and form, applied in warehouse shelving.
DP600 High-Strength Annealed Steel Coil for Structural Components
Dual-phase (DP600) high-strength steel coil, cold-rolled to 0.6 mm thickness and 700 mm width, annealed for automotive structural parts. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Provides a balance of strength and ductility for crash-relevant components.
High-Strength Annealed Steel for HVAC Ducting
Cold-rolled annealed coil of high-strength non-alloy steel, 0.8 mm x 900 mm, certified 290 MPa yield point. This flat-rolled product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 due to its thickness range. Suitable for HVAC ducting requiring strength and formability.
High-Strength Cold-Rolled Annealed Steel Coil for Automotive Panels
High-strength cold-rolled annealed steel coil, 0.7 mm thick and 800 mm wide, used for automotive body panels. It is a flat-rolled product of non-alloy steel, in coils, cold-reduced, not further worked than cold-rolling, and falls under tariff item 7209.17.00 due to its thickness of 0.5 mm or more but not exceeding 1 mm.
High-Strength Cold-Rolled Steel Coil for Automotive Panels
High-strength cold-rolled steel coil, 0.7 mm thick and 1,200 mm wide, with a minimum yield strength of 355 MPa, used for outer body panels in vehicles. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and classified under 7209.17.00 because its thickness is within 0.5-1 mm.
High-Strength Cold-Rolled Steel for Elevator Car Bodies
High-strength cold-rolled steel coil, 0.95 mm thick and 1,300 mm wide, with a 390 MPa minimum yield, used for elevator cabin wall panels. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and falls under 7209.17.00 due to its thickness of 0.5-1 mm.
High-Strength Steel Coil for Agricultural Machinery
High-strength steel coil, cold-rolled to 0.55 mm thickness and 950 mm width, with a 360 MPa yield strength, used for combine harvester hoods. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and classified under 7209.17.00 because its thickness is within 0.5-1 mm.
High-Strength Steel Coil for Heavy Equipment Cabinets
High-strength steel coil, cold-rolled to 0.8 mm thickness and 1,000 mm width, with a 400 MPa yield strength, used for tractor and excavator control cabinets. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and falls under 7209.17.00 due to its thickness of 0.5-1 mm.
High-Strength Steel Coil for Structural Appliances
High-strength steel coil, cold-rolled to 0.9 mm thickness and 900 mm width, with a 380 MPa yield point, used for refrigerator and washer chassis components. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and classified under 7209.17.00 because its thickness is within 0.5-1 mm.
Industrial Annealed High-Strength Steel for Machinery Guards
Industrial annealed high-strength steel coil, 0.65 mm thick and 750 mm wide, used for machinery safety guards. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and classified under 7209.17.00 because its thickness is within 0.5-1 mm.
Ultra BH980 Bake-Hardenable Steel Coil
Bake-hardenable ultra BH980 steel coil, annealed and cold-rolled to a minimum thickness of 0.5 mm. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00. Designed for paint-bake strengthening in automotive outer panels, improving dent resistance after painting.
Ultra DP1000/590 High-Strength Steel Coil
Dual-phase ultra high-strength DP1000/590 annealed steel coil, cold-rolled to 0.9 mm thickness and over 600 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and is classified under tariff item 7209.17.00. Critical for electric vehicle battery enclosures and structural components requiring high strength and crash performance.
Ultra High-Strength TRIP980 Annealed Steel Coil
Transformation-induced plasticity (TRIP) 980 steel coil, cold-rolled and annealed to 0.7 mm thickness. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Ideal for crash-resistant automotive components due to its high strength and energy absorption.
Ultra MS1180 Martensitic Steel Coil
Ultra-strength martensitic MS1180 annealed steel coil, cold-rolled to 0.65 mm thickness and 700 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00. For extreme strength structural auto parts such as B-pillars and roof rails.
Ultra QP980 Quenched Plasticity Steel Coil
Quenching and partitioning (QP) 980 ultra high-strength steel coil, cold-rolled and annealed to 0.75 mm thickness. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Optimized for complex forming in auto body panels requiring high strength and ductility.