Automotive High-Strength Cold-Reduced Steel for Door Frames
Automotive high-strength cold-reduced steel coil, 0.6 mm thick and 1,500 mm wide, with a minimum yield strength of 275 MPa, used for car door inner frames. It is a flat-rolled non-alloy steel product in coils, cold-rolled, not further worked, and falls under 7209.17.00 due to its thickness of 0.5-1 mm.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the thickness exceeds 1 mm
Covers cold-rolled non-alloy steel coils of thickness over 1 mm but not exceeding 3 mm.
If the thickness is less than 0.5 mm
Covers cold-rolled non-alloy steel coils of thickness less than 0.5 mm.
If the width is less than 600 mm
Covers cold-rolled non-alloy steel products of a width less than 600 mm.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Ensure the steel is non-alloy and not clad, plated, or coated; provide documentation of yield strength
• Verify the coil width is at least 600 mm and thickness is within 0.5-1 mm
• Be prepared for possible CBSA requests for chemical analysis to confirm non-alloy status
Related Products under Tariff item 7209.17.00
Advanced AHSS 1180 Steel Annealed Coil
Third-generation advanced high-strength steel (AHSS) 1180 MPa annealed coil, cold-rolled to 0.6 mm thickness and 650 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 because its thickness is between 0.5 mm and 1 mm. Used in high-performance automotive safety components requiring exceptional strength and formability.
Advanced CAHSS Complex Phase Steel Coil
Complex-phase advanced high-strength steel (CAHSS) coil, cold-rolled and annealed to 0.95 mm thickness. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Balances strength and formability for truck panels and structural automotive applications.
Advanced High-Strength DP980 Steel Coil
Cold-rolled dual-phase (DP) 980 MPa high-strength steel coil, annealed, with thickness between 0.5 mm and 1 mm and width exceeding 600 mm. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and is classified under tariff item 7209.17.00. Used in automotive structural components requiring high strength and energy absorption.
Advanced Martensitic MS980 Cold-Rolled Steel Coil
Annealed martensitic MS980 steel coil, cold-rolled to 0.8 mm thickness and 800 mm width. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 due to its thickness range. Designed for lightweight vehicle chassis and structural reinforcements requiring ultra-high strength.
Advanced TWIP Steel High-Strength Coil
Twinning-induced plasticity (TWIP) advanced steel coil, cold-rolled to 0.55 mm thickness and annealed. This flat-rolled non-alloy steel product is in coils, not further worked than cold-rolled, and meets the thickness range of 0.5 mm to 1 mm for tariff item 7209.17.00. Offers high ductility for complex forming applications in vehicles, such as body panels and crash structures.
Annealed High-Strength Steel Coil for Appliance Housings
Cold-rolled non-alloy steel coil, 0.9 mm thick by 1000 mm wide, high-strength grade with 355 MPa yield after annealing. This flat-rolled product is in coils, not further worked than cold-rolled, and falls under tariff item 7209.17.00 due to its thickness range. Used for appliance housings requiring strength and formability.