Of a width of 300 mm or more
Flat-rolled products of stainless steel, of a width of less than 600 mm: > Not further worked than hot-rolled: > Of a thickness of less than 4.75 mm: > Of a width of 300 mm or more
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7220.12.10.00
Hot-Rolled 321 Stabilized Stainless Sheet 2.8mm x 480mm Wide
Titanium-stabilized 321 stainless steel hot-rolled to 2.8 mm thickness and 480 mm width, not further worked. Falls under HTS 7220.12.10.00 for stainless flat-rolled <4.75 mm, >=300 mm wide, hot-rolled surface.
Hot-Rolled 304 Stainless Steel Sheet 1.5mm Thick 400mm Wide
This is a flat-rolled stainless steel sheet made from grade 304 alloy, hot-rolled to a thickness of 1.5 mm and width of 400 mm, not further worked beyond hot-rolling. It falls under HTS 7220.12.10.00 because it is stainless steel, less than 4.75 mm thick, between 300 mm and 600 mm wide, and not subjected to polishing, coating, or other further working as defined in chapter notes.
Hot-Rolled 430 Stainless Steel Coil 3mm Thick 350mm Wide
A coil of hot-rolled 430 ferritic stainless steel, 3 mm thick and 350 mm wide, supplied in annealed pickling condition without additional processing. Classified under HTS 7220.12.10.00 due to stainless steel composition, thickness under 4.75 mm, width 300 mm or more but less than 600 mm, and no further working like coating or burnishing.
Hot-Rolled 316L Stainless Steel Plate 2.5mm x 500mm Wide
Hot-rolled plate of 316L molybdenum-bearing stainless steel, measuring 2.5 mm in thickness and 500 mm width, not in coils and free of patterns or additional treatments. It matches HTS 7220.12.10.00 for stainless flat-rolled products hot-rolled only, under 4.75 mm thick, and 300 mm or wider but under 600 mm.
Annealed Hot-Rolled 201 Stainless Steel Sheet 1.2mm Thick 320mm
Lean duplex 201 stainless steel sheet hot-rolled to 1.2 mm thickness and 320 mm width, annealed but not further worked. Fits HTS 7220.12.10.00 as stainless steel flat-rolled product under 4.75 mm thick, 300+ mm wide, without polishing or chemical treatments.
Hot-Rolled Duplex 2205 Stainless Steel 3.8mm x 450mm Wide
Duplex 2205 stainless steel flat-rolled product hot-rolled to 3.8 mm thick and 450 mm wide, not further worked. Classified in HTS 7220.12.10.00 for its stainless alloy, thickness <4.75 mm, width 300-600 mm, and hot-rolled surface condition.
Hot-Rolled 409 Stainless Steel for Exhaust Systems 2mm x 380mm
Ferritic 409 stainless steel sheet hot-rolled to 2 mm thickness and 380 mm width, used in automotive exhausts, without further treatments. Under HTS 7220.12.10.00 as stainless flat-rolled <4.75 mm thick, >=300 mm wide, hot-rolled only.
Hot-Rolled 310 Stainless Heat-Resistant Sheet 3.2mm x 420mm
High-temperature 310 stainless steel hot-rolled sheet, 3.2 mm thick by 420 mm wide, not further worked. Qualifies for HTS 7220.12.10.00: stainless, <4.75 mm thick, 300+ mm wide, hot-rolled condition per chapter notes.
Hot-Rolled 304 Stainless Steel Decorative Panel Blank 1.8mm x 310mm
304 stainless steel hot-rolled blank for decorative panels, 1.8 mm x 310 mm, mill finish only. HTS 7220.12.10.00 applies to this stainless flat-rolled product <4.75 mm thick, 300-600 mm wide, without further working.
Hot-Rolled 17-4 PH Precipitation Hardening Stainless 3.5mm x 390mm
17-4 PH martensitic precipitation hardening stainless steel sheet hot-rolled, 3.5 mm thick x 390 mm wide, condition A (annealed), no further working. HTS 7220.12.10.00: stainless flat-rolled product, thickness <4.75 mm, width 300+ mm.