Type 410 Cold-Rolled Stainless Steel Coil
Cold-rolled stainless steel coil of Type 410 grade, featuring 11-13% chromium content (less than 15%), with thickness between 0.5 mm and 1 mm, and width exceeding 600 mm. Classified under HTS 7219.34.00.30 as a flat-rolled product not further worked beyond cold-rolling, in coils, meeting the specific dimensional and composition criteria. Used in applications requiring moderate corrosion resistance and good formability.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness under 0.5 mm
Thinner cold-rolled stainless steel coils fall under the subheading for products of a thickness of less than 0.5 mm.
If further worked (e.g., polished surface)
Any surface treatment beyond cold-rolling, like polishing or coating, moves it to further worked categories per Chapter 72 notes.
If width under 600 mm
Flat-rolled stainless steel products narrower than 600 mm are classified under Chapter 72 heading 7220 for narrower widths.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Certify chromium content below 15% by weight with mill test reports to avoid reclassification to higher chromium subheadings
• Verify cold-rolling process documentation; any polishing or coating would shift to 'further worked' categories like 7219.35
• Ensure accurate thickness measurement (0.5-1mm) and coil format, as deviations lead to common CBP reclassification errors
Related Products under HTS 7219.34.00.30
Martensitic 420 Stainless Steel Cold-Reduced Coil
Cold-reduced coil of 420 martensitic stainless steel with approximately 13% chromium (under 15% limit), thickness 0.5-1 mm, coil width 600 mm or more. Fits HTS 7219.34.00.30 as not further worked than cold-rolled, in coils, for heat-treatable applications like cutlery blanks. Provides good hardness after heat treatment with adequate corrosion resistance.
11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
Cold-rolled stainless steel coil with 11% chromium content, 0.7 mm thickness, width 750 mm, supplied in coils for stamping automotive exterior trim. HTS 7219.34.00.30 applies due to cold-rolled (not further worked) state, precise thickness range, wide format, and low chromium per Chapter 72 note (a).
Low Chromium 430-Modified Cold-Rolled Steel Coil
Modified 430 series cold-rolled stainless coil with 14.5% chromium (below 15%), 0.8 mm thick, 1000 mm wide coils for appliance panels. Classified in HTS 21.34.00.30 for flat-rolled stainless, cold-reduced only, specific thickness, low Cr content per US note definitions.
Cold-Rolled 1.4003 Stainless Steel Coil
EN 1.4003 (X2CrNi12) cold-rolled stainless steel coil with 11-12.5% Cr, 0.6 mm thickness, 800 mm width for industrial ducting fabrication. Meets HTS 7219.34.00.30 criteria: stainless, cold-rolled only, 0.5-1 mm thick coil over 600 mm wide, <15% Cr.
Automotive Grade Cold-Reduced Stainless Coil 0.75mm
Special cold-reduced stainless steel coil for automotive exhaust components, 13% Cr, exactly 0.75 mm thick, 700 mm wide coils. HTS 7219.34.00.30 due to cold-rolled state, intermediate thickness band, wide coil format, and chromium below threshold.
Appliance Door Panel Cold-Rolled Stainless Coil
Cold-rolled stainless coil (12.8% Cr) at 0.9 mm thickness, 1200 mm wide for forming refrigerator door panels. Precisely matches HTS 7219.34.00.30 as flat-rolled stainless steel, not further worked than cold-rolled, in coils, correct dimensions and low chromium.