11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
Cold-rolled stainless steel coil with 11% chromium content, 0.7 mm thickness, width 750 mm, supplied in coils for stamping automotive exterior trim. HTS 7219.34.00.30 applies due to cold-rolled (not further worked) state, precise thickness range, wide format, and low chromium per Chapter 72 note (a).
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If of thickness over 1 mm but not over 3 mm
Adjacent thickness band for cold-rolled stainless steel in coils changes the 10-digit HTS code.
If alloy steel with tool steel composition
If meeting tool steel definition in Chapter 72 note (e), it shifts to Chapter 72 heading 7225 for alloy steel bars.
If hot-rolled rather than cold-rolled
Hot-rolled flat products of stainless steel precede cold-rolled in the tariff schedule under heading 7210.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Include end-use statement if for automotive; however, classification is based on objective characteristics, not declared use
• Avoid surface contaminants like oil residue that could be interpreted as 'further worked' chemical treatment
• Batch test for chromium content uniformity, as variations could trigger reclassification across subheadings
Related Products under HTS 7219.34.00.30
Type 410 Cold-Rolled Stainless Steel Coil
Cold-rolled stainless steel coil of Type 410 grade, featuring 11-13% chromium content (less than 15%), with thickness between 0.5 mm and 1 mm, and width exceeding 600 mm. Classified under HTS 7219.34.00.30 as a flat-rolled product not further worked beyond cold-rolling, in coils, meeting the specific dimensional and composition criteria. Used in applications requiring moderate corrosion resistance and good formability.
Martensitic 420 Stainless Steel Cold-Reduced Coil
Cold-reduced coil of 420 martensitic stainless steel with approximately 13% chromium (under 15% limit), thickness 0.5-1 mm, coil width 600 mm or more. Fits HTS 7219.34.00.30 as not further worked than cold-rolled, in coils, for heat-treatable applications like cutlery blanks. Provides good hardness after heat treatment with adequate corrosion resistance.
Low Chromium 430-Modified Cold-Rolled Steel Coil
Modified 430 series cold-rolled stainless coil with 14.5% chromium (below 15%), 0.8 mm thick, 1000 mm wide coils for appliance panels. Classified in HTS 21.34.00.30 for flat-rolled stainless, cold-reduced only, specific thickness, low Cr content per US note definitions.
Cold-Rolled 1.4003 Stainless Steel Coil
EN 1.4003 (X2CrNi12) cold-rolled stainless steel coil with 11-12.5% Cr, 0.6 mm thickness, 800 mm width for industrial ducting fabrication. Meets HTS 7219.34.00.30 criteria: stainless, cold-rolled only, 0.5-1 mm thick coil over 600 mm wide, <15% Cr.
Automotive Grade Cold-Reduced Stainless Coil 0.75mm
Special cold-reduced stainless steel coil for automotive exhaust components, 13% Cr, exactly 0.75 mm thick, 700 mm wide coils. HTS 7219.34.00.30 due to cold-rolled state, intermediate thickness band, wide coil format, and chromium below threshold.
Appliance Door Panel Cold-Rolled Stainless Coil
Cold-rolled stainless coil (12.8% Cr) at 0.9 mm thickness, 1200 mm wide for forming refrigerator door panels. Precisely matches HTS 7219.34.00.30 as flat-rolled stainless steel, not further worked than cold-rolled, in coils, correct dimensions and low chromium.