Containing less than 15 percent by weight of chromium
Flat-rolled products of stainless steel, of a width of 600 mm or more: > Not further worked than cold-rolled (cold-reduced): > Of a thickness of 0.5 mm or more but not exceeding 1 mm > In coils: > Other: > Other: > Containing less than 15 percent by weight of chromium
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7219.34.00.30
Type 410 Cold-Rolled Stainless Steel Coil
Cold-rolled stainless steel coil of Type 410 grade, featuring 11-13% chromium content (less than 15%), with thickness between 0.5 mm and 1 mm, and width exceeding 600 mm. Classified under HTS 7219.34.00.30 as a flat-rolled product not further worked beyond cold-rolling, in coils, meeting the specific dimensional and composition criteria. Used in applications requiring moderate corrosion resistance and good formability.
Martensitic 420 Stainless Steel Cold-Reduced Coil
Cold-reduced coil of 420 martensitic stainless steel with approximately 13% chromium (under 15% limit), thickness 0.5-1 mm, coil width 600 mm or more. Fits HTS 7219.34.00.30 as not further worked than cold-rolled, in coils, for heat-treatable applications like cutlery blanks. Provides good hardness after heat treatment with adequate corrosion resistance.
11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
Cold-rolled stainless steel coil with 11% chromium content, 0.7 mm thickness, width 750 mm, supplied in coils for stamping automotive exterior trim. HTS 7219.34.00.30 applies due to cold-rolled (not further worked) state, precise thickness range, wide format, and low chromium per Chapter 72 note (a).
Low Chromium 430-Modified Cold-Rolled Steel Coil
Modified 430 series cold-rolled stainless coil with 14.5% chromium (below 15%), 0.8 mm thick, 1000 mm wide coils for appliance panels. Classified in HTS 21.34.00.30 for flat-rolled stainless, cold-reduced only, specific thickness, low Cr content per US note definitions.
Cold-Rolled 1.4003 Stainless Steel Coil
EN 1.4003 (X2CrNi12) cold-rolled stainless steel coil with 11-12.5% Cr, 0.6 mm thickness, 800 mm width for industrial ducting fabrication. Meets HTS 7219.34.00.30 criteria: stainless, cold-rolled only, 0.5-1 mm thick coil over 600 mm wide, <15% Cr.
Automotive Grade Cold-Reduced Stainless Coil 0.75mm
Special cold-reduced stainless steel coil for automotive exhaust components, 13% Cr, exactly 0.75 mm thick, 700 mm wide coils. HTS 7219.34.00.30 due to cold-rolled state, intermediate thickness band, wide coil format, and chromium below threshold.
Appliance Door Panel Cold-Rolled Stainless Coil
Cold-rolled stainless coil (12.8% Cr) at 0.9 mm thickness, 1200 mm wide for forming refrigerator door panels. Precisely matches HTS 7219.34.00.30 as flat-rolled stainless steel, not further worked than cold-rolled, in coils, correct dimensions and low chromium.
HVAC Duct Stainless Cold-Rolled Coil 0.55mm
Thin-gauge cold-rolled stainless coil with 11.5% Cr for HVAC duct fabrication, 0.55 mm thick, 650 mm width in coils. HTS 7219.34.00.30 classification reflects cold-reduced processing only, thickness within 0.5-1 mm band, wide format, chromium under 15%.
Ferritic X6Cr13 Cold-Rolled Stainless Coil
X6Cr13 ferritic stainless steel cold-rolled coil, 13% Cr max, 0.65 mm x 900 mm wide for chemical processing equipment. Fits HTS 7219.34.00.30: cold-rolled stainless flat product in coils, precise thickness, <15% Cr per tariff description.
0.9mm Thick Low-Cr Cold-Rolled Stainless Master Coil
Master coil of cold-rolled stainless steel (12% Cr), 0.9 mm nominal thickness, 1500 mm wide for slitting into narrower coils. HTS 7219.34.00.30 as not further worked cold-rolled product in wide coil format, thickness band 0.5-1 mm, chromium <15%.