Automotive Grade Cold-Reduced Stainless Coil 0.75mm
Special cold-reduced stainless steel coil for automotive exhaust components, 13% Cr, exactly 0.75 mm thick, 700 mm wide coils. HTS 7219.34.00.30 due to cold-rolled state, intermediate thickness band, wide coil format, and chromium below threshold.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If hot-rolled and of specific high-strength composition
Hot-rolled high-strength steel per note (a) has dedicated subheadings with different rates.
If width under 600 mm and plated
Narrower galvanized or coated steel sheets classify under heading 7217.
If tool steel alloy composition
Tool steel meeting Chapter 72 note (e) criteria shifts to other alloy flat-rolled products.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Automotive importers should prepare for potential Section 232 tariff applicability on top of normal MFN rates
• Maintain chain-of-custody documentation from melt to coil to prove cold-rolled-only processing
• Watch for minimum yield strength; high-strength per note (a) could affect quotas or special provisions
Related Products under HTS 7219.34.00.30
Type 410 Cold-Rolled Stainless Steel Coil
Cold-rolled stainless steel coil of Type 410 grade, featuring 11-13% chromium content (less than 15%), with thickness between 0.5 mm and 1 mm, and width exceeding 600 mm. Classified under HTS 7219.34.00.30 as a flat-rolled product not further worked beyond cold-rolling, in coils, meeting the specific dimensional and composition criteria. Used in applications requiring moderate corrosion resistance and good formability.
Martensitic 420 Stainless Steel Cold-Reduced Coil
Cold-reduced coil of 420 martensitic stainless steel with approximately 13% chromium (under 15% limit), thickness 0.5-1 mm, coil width 600 mm or more. Fits HTS 7219.34.00.30 as not further worked than cold-rolled, in coils, for heat-treatable applications like cutlery blanks. Provides good hardness after heat treatment with adequate corrosion resistance.
11% Chromium Cold-Rolled Stainless Coil for Automotive Trim
Cold-rolled stainless steel coil with 11% chromium content, 0.7 mm thickness, width 750 mm, supplied in coils for stamping automotive exterior trim. HTS 7219.34.00.30 applies due to cold-rolled (not further worked) state, precise thickness range, wide format, and low chromium per Chapter 72 note (a).
Low Chromium 430-Modified Cold-Rolled Steel Coil
Modified 430 series cold-rolled stainless coil with 14.5% chromium (below 15%), 0.8 mm thick, 1000 mm wide coils for appliance panels. Classified in HTS 21.34.00.30 for flat-rolled stainless, cold-reduced only, specific thickness, low Cr content per US note definitions.
Cold-Rolled 1.4003 Stainless Steel Coil
EN 1.4003 (X2CrNi12) cold-rolled stainless steel coil with 11-12.5% Cr, 0.6 mm thickness, 800 mm width for industrial ducting fabrication. Meets HTS 7219.34.00.30 criteria: stainless, cold-rolled only, 0.5-1 mm thick coil over 600 mm wide, <15% Cr.
Appliance Door Panel Cold-Rolled Stainless Coil
Cold-rolled stainless coil (12.8% Cr) at 0.9 mm thickness, 1200 mm wide for forming refrigerator door panels. Precisely matches HTS 7219.34.00.30 as flat-rolled stainless steel, not further worked than cold-rolled, in coils, correct dimensions and low chromium.