Monel K-500 Round Corner Square Profile
Monel K-500 round corner square profile, a square profile with radiused corners made from age-hardenable Monel K-500. It is used for propeller shafts. The specific geometry qualifies as a profile under nickel alloys because it does not conform to the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes, or pipes.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | — | Free |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the profile is made of nickel, not alloyed
This subheading covers bars, rods and profiles of nickel, not alloyed, which would apply if the material is at least 99% nickel plus cobalt with specified limits.
If the square profile is further worked to become an article
Other articles of nickel are classified under this subheading if the product is no longer a profile as defined in Section XV.
If the profile is presented as a shaft
Transmission shafts are classified under this heading, which would apply if the product is dedicated for use as a propeller shaft.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Confirm the square profile's dimensions, including the radiused corners, to ensure it is not classified as a bar or rod
• Provide a certificate of analysis confirming the Monel K-500 composition for customs verification
• If the profile is used for propeller shafts, consider whether it may be subject to Canadian marine regulations
Related Products under Tariff item 7505.12.00
625 Alloy Cold-Formed Nickel Shaft Blank
Cold-formed shaft blanks made from Inconel 625, a nickel-chromium-molybdenum alloy, designed for machining into pump and compressor components for power generation. The cold-forming process imparts improved mechanical properties while maintaining the alloy's excellent corrosion resistance.
625L Nickel Alloy Forging Bar
Inconel 625L is a low-carbon variant of the Inconel 625 nickel-chromium-molybdenum alloy, forged into bars for nuclear reactor components. The upset-forging process and non-cold-formed condition place it under tariff item 7505.12.00 as a bar of nickel alloy.
AL-6XN Cold-Formed Nickel Rod
Cold-formed rods made from AL-6XN, a super-austenitic nickel alloy with high molybdenum content, used in seawater desalination and pulp bleaching equipment. The cold-forming process enhances strength while preserving the alloy's resistance to chloride stress corrosion cracking.
AL-6XN Nickel Alloy Rod
AL-6XN is a super-austenitic stainless steel with high nickel content, supplied as annealed rods for seawater desalination plants. The rod form and nickel alloy composition classify it under tariff item 7505.12.00.
Alloy 20 Cold-Formed Nickel-Iron Rod
Cold-formed rods made from Alloy 20 (UNS N08020), a nickel-iron-chromium alloy with copper and molybdenum additions, designed for handling sulfuric acid in industrial piping systems. The cold-forming process improves dimensional accuracy and surface finish compared to hot-rolled equivalents.
Alloy 20 Nickel Profile Flat Bar
Alloy 20 nickel profile flat bar, a rectangular profile with a specific width-to-thickness ratio, made from Alloy 20 nickel-iron-chromium alloy. It is designed for use in sulfuric acid handling equipment. It is classified as a nickel alloy profile because its cross-section does not meet the definition of bars, rods, wire, plates, sheets, strip, foil, tubes, or pipes.