High-Strength Steel Coil for Wind Turbine Components
Cold-rolled high-strength steel coil, 1.9 mm thick and 1250 mm wide, with a yield point of 370 MPa, used for wind turbine nacelle supports. It is a flat-rolled product of non-alloy steel, in coils, not further worked than cold-rolled, and not clad, plated or coated. The thickness falls within 1-3 mm, so it is classified under tariff item 7209.16.00.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the steel contains alloying elements (e.g., chromium, nickel)
Alloy steel flat-rolled products are in heading 7225.
If the thickness is reduced to 0.5-1 mm
Thinner coils fall under a different subheading.
If the thickness is increased to 3 mm or more
Thicker coils are classified under 7209.15.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Confirm the steel is non-alloy and high-strength (yield ≥ 275 MPa) with a mill certificate
• Ensure the coil width is at least 600 mm and thickness is between 1 and 3 mm
• If the steel is alloyed, it would be classified under heading 7225 instead
Related Products under Tariff item 7209.16.00
Advanced AHSS Martensitic MS1200 Steel Coil
Martensitic 1200 MPa advanced high-strength steel coil, cold-rolled 1.8 mm thick, 1000 mm wide, annealed condition. It falls under this item as a flat-rolled product of iron or non-alloy steel, cold-rolled, not clad, plated or coated, within the specified thickness range.
Advanced High-Strength DP980 Steel Coil
Cold-rolled dual-phase (DP) 980 MPa high-strength steel coil, thickness 1.5 mm, width 1200 mm, annealed for automotive use. It is classified under this item as a cold-rolled non-alloy steel product within the specified thickness range.
Annealed Cold-Reduced Steel for HVAC Ductwork
Annealed cold-reduced non-alloy steel coil, 1.2 mm thick and 1000 mm wide, continuously annealed for HVAC ductwork fabrication requiring high cleanliness. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled (cold-reduced), and not clad, plated or coated. The thickness of 1.2 mm places it within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed Cold-Rolled Steel Coil for Automotive Panels
Annealed cold-rolled non-alloy steel coil, 1.5 mm thick and over 600 mm wide, specifically annealed to achieve uniform microstructure and improved formability for automotive panels. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, and not clad, plated or coated. The thickness of 1.5 mm falls within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed CR Steel Coil for Home Appliance Housings
Annealed cold-rolled non-alloy steel coil, 2.0 mm thick and 1200 mm wide, annealed for enhanced ductility, used in refrigerator and washer exteriors. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, and not clad, plated or coated. The thickness of 2.0 mm places it within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed High-Strength Steel Coil for Heavy Machinery Frames
Annealed high-strength steel coil for heavy machinery frames, cold-rolled to 1.5-2.5 mm thickness and 800 mm width, of non-alloy steel with yield strength exceeding 275 MPa. It is classified under tariff item 7209.16.00 as a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, with thickness between 1 mm and 3 mm.