Grade 80 High-Strength Cold-Rolled Steel Coil
Grade 80 high-strength cold-rolled steel coil, a high-strength low-alloy equivalent non-alloy steel, cold-rolled to 1.2 mm thickness and 1600 mm width, with minimum yield of 550 MPa. It is classified under tariff item 7209.16.00 as a flat-rolled product in coils, not further worked than cold-rolled, with thickness exceeding 1 mm but less than 3 mm.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the steel is alloy steel
HSLA steels with alloying elements above Chapter 72 thresholds are classified under heading 7225.
If the thickness is 1 mm or less
Thinner cold-rolled steel coils fall under a different subheading.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Verify the steel is non-alloy despite the HSLA-equivalent designation, as some grades contain alloying elements
• Provide documentation of yield strength and composition to the CBSA
• Ensure the coil width exceeds 600 mm and thickness is within 1-3 mm
Related Products under Tariff item 7209.16.00
Advanced AHSS Martensitic MS1200 Steel Coil
Martensitic 1200 MPa advanced high-strength steel coil, cold-rolled 1.8 mm thick, 1000 mm wide, annealed condition. It falls under this item as a flat-rolled product of iron or non-alloy steel, cold-rolled, not clad, plated or coated, within the specified thickness range.
Advanced High-Strength DP980 Steel Coil
Cold-rolled dual-phase (DP) 980 MPa high-strength steel coil, thickness 1.5 mm, width 1200 mm, annealed for automotive use. It is classified under this item as a cold-rolled non-alloy steel product within the specified thickness range.
Annealed Cold-Reduced Steel for HVAC Ductwork
Annealed cold-reduced non-alloy steel coil, 1.2 mm thick and 1000 mm wide, continuously annealed for HVAC ductwork fabrication requiring high cleanliness. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled (cold-reduced), and not clad, plated or coated. The thickness of 1.2 mm places it within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed Cold-Rolled Steel Coil for Automotive Panels
Annealed cold-rolled non-alloy steel coil, 1.5 mm thick and over 600 mm wide, specifically annealed to achieve uniform microstructure and improved formability for automotive panels. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, and not clad, plated or coated. The thickness of 1.5 mm falls within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed CR Steel Coil for Home Appliance Housings
Annealed cold-rolled non-alloy steel coil, 2.0 mm thick and 1200 mm wide, annealed for enhanced ductility, used in refrigerator and washer exteriors. It is a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, and not clad, plated or coated. The thickness of 2.0 mm places it within tariff item 7209.16.00 (exceeding 1 mm but less than 3 mm).
Annealed High-Strength Steel Coil for Heavy Machinery Frames
Annealed high-strength steel coil for heavy machinery frames, cold-rolled to 1.5-2.5 mm thickness and 800 mm width, of non-alloy steel with yield strength exceeding 275 MPa. It is classified under tariff item 7209.16.00 as a flat-rolled product of iron or non-alloy steel, in coils, not further worked than cold-rolled, with thickness between 1 mm and 3 mm.