With a thickness of 6.3 mm or less
Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm: > Other: > Of aluminum, not alloyed: > Not clad > With a thickness of 6.3 mm or less
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7606.91.30.95
1050 Aluminum Sheet 3mm Thick
A rectangular sheet of unalloyed 1050 aluminum with 99.5% purity and thickness of 3mm, used for general fabrication. It falls under HTS 7606.91.30.95 as it is not clad, rectangular, exceeds 0.2mm but not 6.3mm thick, and meets the non-alloyed aluminum definition (Fe+Si ≤0.1%). Ideal for lightweight structural components.
1100 Aluminum Plate 4mm Thick
Unclad 1100 grade aluminum plate, 4mm thick, with high purity for corrosion-resistant applications like chemical tanks. Classified in 7606.91.30.95 due to non-alloyed composition, plate/sheet form, and thickness between 0.2mm and 6.3mm.
1070 Pure Aluminum Sheet 2.5mm
High-purity 1070 aluminum sheet at 2.5mm thickness, used in electronics reflectors. Meets HTS 7606.91.30.95 as rectangular, rolled, unclad, non-alloyed (≥99.7% Al), thickness 0.2-6.3mm.
1060 Aluminum Flat Sheet 5mm Thick
Commercial pure 1060 aluminum flat sheet, 5mm thick for signage and cladding. Under 7606.91.30.95: non-alloyed per note (a), not clad, thickness ≤6.3mm.
3003 Aluminum Sheet 3mm - Wait, Non-Alloy Only
99% pure aluminum sheet 6mm thick for architectural panels, meeting strict non-alloy specs. HTS 7606.91.30.95 applies to this rolled, unclad plate/sheet.
1050 H14 Aluminum Sheet 4.5mm
Tempered H14 1050 aluminum sheet 4.5mm thick for trailer skins. Non-alloyed, flat rolled sheet under 7606.91.30.95 thickness spec.
1100 O Temper Sheet 2mm Thick
Annealed O temper 1100 aluminum sheet 2mm for soft forming applications. Pure non-alloyed per definition, ≤6.3mm thick sheet.
1070 Mirror Finish Sheet 1mm
Polished mirror finish 1070 sheet 1mm for decorative reflectors. Still basic rolled sheet, non-alloyed, no further working.
Non-Alloyed Al Treadplate 5.5mm
1050 aluminum treadplate sheet 5.5mm with raised pattern for flooring.
Pure Al Roofing Sheet 3.2mm
Corrugated pure Al sheet 3.2mm for roofing, rolled form.
1050 Fin Stock Sheet 0.5mm
Thin 1050 sheet 0.5mm for heat exchanger fins.
1100 Battery Sheet 4mm
Sheet for battery casings, pure Al 4mm.
1070 Lighting Reflector Sheet 2.8mm
Reflective sheet for fixtures.
Pure Al Nameplate Sheet 1.2mm
Sheet for engraving nameplates.
1145 Aluminum Sheet 1.5mm Thick
1145 non-alloyed aluminum sheet, 1.5mm thick, for fin stock in heat exchangers. Fits 7606.91.30.95: pure Al base, rectangular sheet, no cladding, specified thickness range.