AISI 304 Stainless Steel Sheet 2B Finish
Flat-rolled stainless steel sheet conforming to AISI 304 grade, containing approximately 8-10.5% nickel and 18-20% chromium, with a 2B cold-rolled finish. Width exceeds 600 mm, typically 1.5 mm thick, not further worked beyond basic rolling and annealing. Classifies under 7219.90.0025 due to nickel content over 0.5%, width over 600 mm, and exclusion from other specific subheadings.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If containing ≤0.5% nickel
Lower nickel content moves it to the 'not containing >0.5% nickel' subheading within the same 'other' flat-rolled stainless category.
If width <600 mm
Narrower products under 600 mm width but over 300 mm classify under the corresponding narrow strip provisions in 7219.31.
If not stainless steel (e.g., <10.5% chromium)
Lacks sufficient chromium alloying per chapter note (e), shifting from stainless steel Chapter 72 heading 7219 to non-stainless 7220.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Provide mill test certificate (MTC) verifying chemical composition, especially nickel >0.5% and chromium content, to confirm stainless steel classification
• Ensure accurate thickness/width measurements; products ≤600mm width shift to chapter 72 heading 7220
• Avoid claims for rust/discoloration allowances per chapter note—no duty reduction for pre-entry surface issues
Related Products under HTS 7219.90.00.25
AISI 316L Stainless Steel Plate No.1 Finish
Hot-rolled stainless steel plate AISI 316L grade with 10-14% nickel, 16-18% chromium, and low carbon, featuring No.1 finish (scale not fully removed). Thickness 6 mm, width 1500 mm, used in chemical processing. Fits 7219.90.0025 as flat-rolled stainless steel >600 mm wide, >0.5% Ni, not in prior 'other' subheadings.
Duplex 2205 Stainless Steel Sheet Annealed
Duplex 2205 (UNS S32205) stainless steel sheet with ~5.5-6.5% nickel, 22% chromium, 3% molybdenum, annealed condition, 3 mm thick x 1250 mm wide. High strength for marine applications. Under 7219.90.0025 for stainless flat-rolled >600 mm, >0.5% Ni, not tool/heat-resisting per chapter notes.
Nitronic 60 Stainless Steel Strip Coil
Nitronic 60 (UNS S21800) high-manganese austenitic stainless strip in coil form, 8% nickel, 17% Cr, 1 mm thick x 800 mm wide. Used for wear-resistant parts. Classifies 7219.90.0025 as other flat-rolled stainless >600 mm, >0.5% Ni.
AISI 321 Stainless Steel Sheet Bright Annealed
Stabilized AISI 321 stainless sheet with 9-12% nickel, 17-19% Cr, titanium-stabilized, bright annealed finish, 2 mm x 1200 mm. For welded fabrications. 7219.90.0025 as other stainless flat-rolled >600 mm wide.
AISI 310 Stainless Steel Hot Band
AISI 310 high-temperature stainless hot band (not pickled), 20-22% Ni, 24-26% Cr, 4 mm thick x 1500 mm wide coil. For furnace parts. Under 7219.90.0025 as Ni>0.5% flat-rolled stainless.
17-4 PH Precipitation Hardening Stainless Sheet
17-4 PH (UNS S17400) martensitic PH stainless sheet, 3-5% Ni, 15-17.5% Cr, 4% Cu, H900 condition, 1.5 mm x 1000 mm. Aerospace grade. 7219.90.0025 for Ni>0.5% stainless flat.