Other
Flat-rolled products of stainless steel, of a width of 600 mm or more: > Not further worked than cold-rolled (cold-reduced): > Of a thickness exceeding 1 mm but less than 3 mm > In coils: > Other: > Other: > Other: > Other
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7219.33.00.44
17-4 PH Precipitation Hardening Stainless Coil 2.0mm
Precipitation hardening 17-4 PH stainless steel coil, cold-rolled 2 mm thick, 1300 mm wide. HTS 7219.33.0044 for this martensitic cold-rolled stainless not matching specialty notes. High strength for aerospace components.
Duplex 2205 Cold-Rolled Stainless Steel Coil 1.4mm
Duplex 2205 stainless coil with high strength/corrosion resistance, cold-rolled 1.4 mm, 1700 mm wide. Under HTS 7219.33.0044 as other cold-rolled stainless coil specs. For oil/gas piping.
AISI 301 Cold-Rolled Stainless Steel Coil 2.8mm
High strength AISI 301 stainless coil, cold-rolled to 2.8 mm thick, 900 mm wide. HTS 7219.33.0044 for general cold-rolled stainless dimensions. Spring temper for automotive.
439 Cold-Rolled Stainless Steel Coil 1.9mm Thick
Ferritic 439 stainless coil for exhaust, cold-rolled 1.9 mm, 1550 mm wide. Fits HTS 7219.33.0044 specs perfectly.
AISI 304L Low Carbon Stainless Coil 2.4mm
Low carbon 304L stainless coil, cold-rolled 2.4 mm, 2000 mm wide. HTS 7219.33.0044 classification.
316Ti Stabilized Stainless Coil 1.3mm
316Ti stainless coil cold-rolled 1.3 mm for weldability. HTS 7219.33.0044.
AISI 420 Martensitic Stainless Coil 2.1mm
Martensitic 420 stainless coil 2.1 mm cold-rolled. HTS 7219.33.0044.
Nitronic 60 Cold-Rolled Stainless Coil 1.7mm
High strength Nitronic 60 coil 1.7 mm thick. HTS 7219.33.0044.
AISI 304 Cold-Rolled Stainless Steel Coil 2mm Thick
Cold-rolled stainless steel coil made from AISI 304 grade, measuring 2 mm thick and 1500 mm wide, supplied in coils weighing up to 20 tons. This product falls under HTS 7219.33.0044 as it is flat-rolled stainless steel, not further worked beyond cold-rolling, with thickness between 1-3 mm, width over 600 mm, and classified as 'other' non-specialty steel. Commonly used for manufacturing kitchen equipment and architectural panels.
AISI 316L Cold-Rolled Stainless Steel Coil 1.5mm
High corrosion-resistant AISI 316L stainless steel coil, cold-rolled to 1.5 mm thickness, 1200 mm width, in standard coil form. Classified under HTS 7219.33.0044 for cold-rolled stainless steel coils over 1 mm thick but under 3 mm, width ≥600 mm, not further worked, and not fitting specialty definitions. Ideal for chemical processing equipment and marine applications.
430 Grade Cold-Rolled Stainless Steel Coil 2.2mm Thick
Ferritic 430 stainless steel coil cold-rolled to 2.2 mm thickness, 1000 mm wide, in coil form for automotive trim applications. Fits HTS 7219.33.0044 as non-specialty, cold-rolled flat stainless product, width ≥600 mm, thickness 1-3 mm, not further worked. Offers good formability and corrosion resistance for decorative uses.
AISI 201 Cold-Rolled Stainless Steel Coil 1.8mm
Austenitic AISI 201 stainless steel coil, cold-rolled to 1.8 mm thick, 1800 mm wide, suited for consumer goods manufacturing. HTS 7219.33.0044 applies to this general cold-rolled stainless coil not meeting specialty notes, width over 600 mm, 1-3 mm thick. Cost-effective alternative to 304 with good ductility.
409 Cold-Rolled Stainless Steel Coil 1.2mm Thick
Ferritic 409 grade stainless coil cold-rolled to 1.2 mm, 1400 mm width, primarily for exhaust systems. Under HTS 7219.33.0044 as other cold-rolled stainless coils, not further worked, fitting dimensional specs. Provides heat and corrosion resistance at lower cost.
AISI 310 Cold-Rolled Stainless Steel Coil 2.5mm
High-temperature AISI 310 stainless coil, cold-rolled 2.5 mm thick, 1600 mm wide, in coils. HTS 7219.33.0044 covers this non-specialty cold-rolled flat stainless product meeting width/thickness criteria, not further worked. Used in furnace parts and heat exchangers.
321 Stabilized Cold-Rolled Stainless Steel Coil 1.6mm
Titanium-stabilized AISI 321 stainless coil, cold-rolled to 1.6 mm, 1100 mm wide. Classifies in HTS 7219.33.0044 as standard cold-rolled stainless coil, width ≥600 mm, 1-3 mm thick, other category. Weldable grade for aircraft and pressure vessels.