High-Strength Cold-Rolled Annealed Steel Coil for Automotive Panels
Flat-rolled high-strength steel coil, cold-rolled to 0.7 mm thickness and 800 mm width, annealed for improved formability. Classified under HTS 7209.17.00.45 as nonalloy high-strength steel (yield point ≥275 MPa for <3 mm thickness), in coils, not further worked beyond cold-rolling and annealing. Used primarily for outer body panels in vehicles requiring strength and ductility.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness under 0.5 mm
Thinner cold-rolled high-strength steel coils fall under the subheading for gauges below 0.5 mm.
If width under 600 mm
Narrower coils (under 600 mm width) are classified in heading 7211 for cold-rolled products of narrower dimension.
If alloy steel composition
Products meeting alloy steel definitions (e.g., specific chromium content) shift to Chapter 72 alloy steel headings.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Certify minimum yield strength of 275 MPa at entry with mill test reports to qualify as high-strength steel per US notes
• Ensure precise thickness measurement (0.5-1 mm) and annealing documentation to prevent reclassification to thinner gauges
• Verify no cladding, plating, or coatings; even minor surface treatments trigger 'further worked' exclusion
Related Products under HTS 7209.17.00.45
Annealed High-Strength Steel Coil for Appliance Housings
Cold-rolled nonalloy steel coil, 0.9 mm thick by 1000 mm wide, high-strength grade with 355 MPa yield after annealing. Fits HTS 7209.17.00.45 as flat-rolled iron/nonalloy steel in coils, cold-reduced, annealed but not further worked. Ideal for refrigerator and washer outer casings needing dent resistance.
DP600 High-Strength Annealed Steel Coil for Structural Components
Dual-phase (DP600) high-strength steel coil, cold-rolled to 0.6 mm thickness, 700 mm width, annealed for automotive structural parts. HTS 7209.17.00.45 applies to this nonalloy high-strength steel (meeting 275 MPa minimum yield), in coil form without further processing beyond cold-reduction and annealing.
High-Strength Annealed Steel for HVAC Ducting
Cold-rolled annealed coil of high-strength nonalloy steel, 0.8 mm x 900 mm, certified 290 MPa yield point. Under HTS 7209.17.00.45 for flat-rolled products of 600+ mm width, 0.5-1 mm thick, in coils not further worked. Suited for heavy-duty HVAC duct fabrication.
Automotive Grade Annealed HSLA Steel Coil
High-strength low-alloy (HSLA) steel coil, cold-rolled 0.75 mm thick, 1200 mm wide, annealed, 300 MPa minimum yield. HTS 7209.17.00.45 covers this nonalloy flat-rolled product in coils, meeting thickness/strength specs without cladding or further working.
Annealed High-Strength Steel Coil for Furniture Frames
Cold-reduced high-strength steel coil, 0.55 mm x 650 mm, annealed, suitable for heavy-duty furniture reinforcement. Classifies in HTS 7209.17.00.45 as 600+ mm wide, 0.5-1 mm thick nonalloy high-strength steel in coils, annealed only.
Industrial Annealed High-Strength Steel for Machinery Guards
0.65 mm thick cold-rolled annealed coil, 750 mm wide, high-strength nonalloy steel for machinery safety guards. HTS 7209.17.00.45 due to coil form, precise thickness, high-strength certification, and lack of further working.