Annealed High-Strength Steel Coil for Appliance Housings
Cold-rolled nonalloy steel coil, 0.9 mm thick by 1000 mm wide, high-strength grade with 355 MPa yield after annealing. Fits HTS 7209.17.00.45 as flat-rolled iron/nonalloy steel in coils, cold-reduced, annealed but not further worked. Ideal for refrigerator and washer outer casings needing dent resistance.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If not annealed
Non-annealed high-strength steel in this thickness range uses different subheading within 7209.18.
If plated or coated
Any metallic or nonmetallic coating (e.g., oil, paint) classifies under 7210 as further worked products.
If hot-rolled instead of cold-rolled
Hot-rolled equivalents remain in heading 7208, even if high-strength and similar dimensions.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Provide chemical composition analysis confirming nonalloy status (< specific alloying limits in US Chapter 72 notes)
• Include annealing process certificates; double-annealed products may require verification of 'not further worked' status
• Check for rust/discoloration claims—US notes prohibit duty reductions for pre-entry surface oxidation
Related Products under HTS 7209.17.00.45
High-Strength Cold-Rolled Annealed Steel Coil for Automotive Panels
Flat-rolled high-strength steel coil, cold-rolled to 0.7 mm thickness and 800 mm width, annealed for improved formability. Classified under HTS 7209.17.00.45 as nonalloy high-strength steel (yield point ≥275 MPa for <3 mm thickness), in coils, not further worked beyond cold-rolling and annealing. Used primarily for outer body panels in vehicles requiring strength and ductility.
DP600 High-Strength Annealed Steel Coil for Structural Components
Dual-phase (DP600) high-strength steel coil, cold-rolled to 0.6 mm thickness, 700 mm width, annealed for automotive structural parts. HTS 7209.17.00.45 applies to this nonalloy high-strength steel (meeting 275 MPa minimum yield), in coil form without further processing beyond cold-reduction and annealing.
High-Strength Annealed Steel for HVAC Ducting
Cold-rolled annealed coil of high-strength nonalloy steel, 0.8 mm x 900 mm, certified 290 MPa yield point. Under HTS 7209.17.00.45 for flat-rolled products of 600+ mm width, 0.5-1 mm thick, in coils not further worked. Suited for heavy-duty HVAC duct fabrication.
Automotive Grade Annealed HSLA Steel Coil
High-strength low-alloy (HSLA) steel coil, cold-rolled 0.75 mm thick, 1200 mm wide, annealed, 300 MPa minimum yield. HTS 7209.17.00.45 covers this nonalloy flat-rolled product in coils, meeting thickness/strength specs without cladding or further working.
Annealed High-Strength Steel Coil for Furniture Frames
Cold-reduced high-strength steel coil, 0.55 mm x 650 mm, annealed, suitable for heavy-duty furniture reinforcement. Classifies in HTS 7209.17.00.45 as 600+ mm wide, 0.5-1 mm thick nonalloy high-strength steel in coils, annealed only.
Industrial Annealed High-Strength Steel for Machinery Guards
0.65 mm thick cold-rolled annealed coil, 750 mm wide, high-strength nonalloy steel for machinery safety guards. HTS 7209.17.00.45 due to coil form, precise thickness, high-strength certification, and lack of further working.