Duplex 2205 Stainless Rectangle Bloom
A duplex 2205 stainless steel bloom in a rectangular cross-section, with a cross-sectional area under 232 cm² and a width less than four times its thickness. It offers high strength for oil and gas valve components. This product falls under tariff item 7218.91.00 as a semi-finished product of stainless steel.
Import Duty Rates by Country of Origin
| Origin Country | MFN Tariff | Surtaxes | Total Effective Rate |
|---|---|---|---|
| 🇨🇳China | Free | — | Free |
| 🇲🇽Mexico | Free | — | Free |
| 🇺🇸United States | Free | +50.0% | 50% |
| 🇩🇪Germany | Free | — | Free |
| 🇯🇵Japan | Free | — | Free |
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If the cross-section is square or round
Other semi-finished stainless steel products are classified under this item.
If the bloom is further worked into angles, shapes, or sections
Angles, shapes, and sections of stainless steel are classified in heading 72.22.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right tariff item — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Ensure the bloom is not further worked than primary hot-rolling or roughly shaped by forging, and that the rectangular cross-section has a width less than 4x the thickness
• Provide a certificate of analysis confirming the duplex 2205 composition (≥10.5% chromium, with nickel and molybdenum)
• Verify the cross-sectional area is under 232 cm² to remain within this tariff item
Related Products under Tariff item 7218.91.00
15-5 PH Stainless Billet 175x115mm
A 15-5 PH stainless steel billet with a rectangular cross-section of 175mm x 115mm, used as semi-finished material for aerospace components. This product is in primary form and has not been further worked beyond initial hot-rolling or forging, qualifying it under tariff item 7218.91.00.
17-4 PH Precipitation Hardening Stainless Billet 280 cm²
A semi-finished rectangular billet of 17-4 PH martensitic precipitation-hardening stainless steel, with a cross-sectional area of 280 cm², exceeding 232 cm². It is used for aerospace forgings. This product is classified under tariff item 7218.91.00 as a semi-finished product of stainless steel, despite the larger cross-section.
17-4 PH Precipitation Hardening Stainless Rectangle
A semi-finished rectangular billet of 17-4 PH martensitic precipitation-hardening stainless steel, with a cross-sectional area under 232 cm² and a width less than four times its thickness. It is used for forging aerospace fasteners and other high-strength components. This product qualifies as a semi-finished product of stainless steel under tariff item 7218.91.00.
17-4 PH Stainless Precipitation Hardening Strip 0.5mm x 180mm
17-4 PH martensitic precipitation-hardening stainless steel hot-rolled strip, measuring 0.5 mm in thickness and 180 mm in width. Despite being described as a strip, its dimensions and semi-finished state place it under tariff item 7218.91.00 as a semi-finished product of stainless steel with a rectangular cross-section.
17-4 PH Stainless Steel Slab 220x160mm
A 17-4 PH stainless steel slab with a rectangular cross-section of 220mm x 160mm, used as feedstock for precision tooling. This semi-finished product is in primary form, not further worked than hot-rolled or forged, and falls under tariff item 7218.91.00.
304 High-Strength Stainless Strip 2.5mm x 600mm
High-strength 304 stainless steel variant, hot-rolled strip measuring 2.5 mm in thickness and 600 mm in width, with a yield strength exceeding 355 MPa. Classified under tariff item 7218.91.00 as a semi-finished product of stainless steel with a rectangular cross-section, intended for structural components.