Round Wire Common Nails 2 Inch
Straight-shank common nails made from one-piece round wire construction of iron or steel, measuring 2 inches in length with a diameter under 16 mm, used for general woodworking and framing. They fall under HTS 7317.00.55.60 as uncoated, unplated nails of one-piece construction from round wire, excluding those with copper heads. No cross-sectional dimension exceeds 16 mm per chapter definition.
Import Duty Rates by Country of Origin
| Origin Country | MFN Rate | Ch.99 Surcharges | Total Effective Rate |
|---|---|---|---|
| šØš³China | Free | +35.0% | 35% |
| š²š½Mexico | Free | +10.0% | 10% |
| šØš¦Canada | Free | +10.0% | 10% |
| š©šŖGermany | Free | +10.0% | 10% |
| šÆšµJapan | Free | +10.0% | 10% |
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If made from wire with deformed or barbed shank
Deformed shanks like ring or spiral change classification within the same heading but different subheading for enhanced holding power.
If produced by cold heading rather than wire forming
Cold-headed nails fall under a separate provision earlier in the tariff, distinguished by manufacturing process.
If imported in collated strips for pneumatic nailers
Collated nails packaged as connected strips for power tools are classified as screws and bolts in heading 7318.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
ā¢ Verify wire diameter does not exceed 16 mm and confirm one-piece construction to avoid reclassification to other subheadings
ā¢ Provide mill test certificates showing no coatings, plating, or paint; common pitfall is residual oil mistaken for coating
ā¢ Label shipments clearly as 'uncoated steel nails' and ensure country-of-melt documentation for steel origin rules
Related Products under HTS 7317.00.55.60
Round Wire Finish Nails 1-1/2 Inch
Slim shank finish nails of one-piece round wire steel construction, 1-1/2 inches long, designed for trim work and cabinetry with small heads for countersinking. Classified under HTS 7317.00.55.60 as other uncoated nails from round wire of one-piece construction. Conforms to chapter wire definition with dimensions under 16 mm.
Round Wire Brad Nails 1 Inch
Very thin round wire brad nails, 1 inch long, of one-piece steel construction for delicate finish work like molding and paneling without splitting wood. Fits HTS 7317.00.55.60 for other uncoated round wire nails not plated or painted. Chapter wire limit of 16 mm cross-section satisfied.
Round Wire Siding Nails 2-1/2 Inch
2-1/2 inch round wire nails of one-piece steel construction for vinyl or wood siding installation, uncoated for clean finishes. HTS 7317.00.55.60 covers these as other non-coated round wire nails. Wire dimensions comply with chapter maximum.
Round Wire Underlayment Nails 1-1/4 Inch
1-1/4 inch ringless round wire nails of one-piece steel for securing floor underlayment, uncoated for subfloor applications. Classified HTS 7317.00.55.60 as other non-coated round wire construction. Chapter wire parameters met.
Round Wire Trim Nails 2 Inch
2-inch round wire trim nails constructed in one piece from steel for baseboards and crown molding, maintained uncoated. Falls under HTS 7317.00.55.60 as other round wire articles not plated/painted. Conforms to wire cross-section limit.
Round Wire Box Nails 1-1/4 Inch
Light-duty box nails made from one-piece round steel wire, 1-1/4 inches long with thinner shanks than common nails for packaging and light framing. HTS 7317.00.55.60 applies to these uncoated articles of round wire construction without plating or paint. Wire cross-section under 16 mm per chapter notes.