Round Wire Brad Nails 1 Inch
Very thin round wire brad nails, 1 inch long, of one-piece steel construction for delicate finish work like molding and paneling without splitting wood. Fits HTS 7317.00.55.60 for other uncoated round wire nails not plated or painted. Chapter wire limit of 16 mm cross-section satisfied.
Import Duty Rates by Country of Origin
| Origin Country | MFN Rate | Ch.99 Surcharges | Total Effective Rate |
|---|---|---|---|
| šØš³China | Free | +35.0% | 35% |
| š²š½Mexico | Free | +10.0% | 10% |
| šØš¦Canada | Free | +10.0% | 10% |
| š©šŖGermany | Free | +10.0% | 10% |
| šÆšµJapan | Free | +10.0% | 10% |
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If specifically over 16 gauge (thinner wire)
Statistical breakout for very fine wire gauges within the round wire one-piece category.
If woven into ornamental braids or trims
Wire formed into textile-like structures for apparel classifies in Chapter 58.
If straight wire sewing pins without heads
Headless straight pins for sewing fall under heading 7319 for sewing needles and pins.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
ā¢ Brad nails under 1 gauge may border on pin classification; measure precisely and document
ā¢ Prevent reclassification by certifying no galvanizing or oil coatings beyond mill lubricant
ā¢ For bulk container shipments, segregate by size/HTS to avoid averaging declarations
Related Products under HTS 7317.00.55.60
Round Wire Common Nails 2 Inch
Straight-shank common nails made from one-piece round wire construction of iron or steel, measuring 2 inches in length with a diameter under 16 mm, used for general woodworking and framing. They fall under HTS 7317.00.55.60 as uncoated, unplated nails of one-piece construction from round wire, excluding those with copper heads. No cross-sectional dimension exceeds 16 mm per chapter definition.
Round Wire Finish Nails 1-1/2 Inch
Slim shank finish nails of one-piece round wire steel construction, 1-1/2 inches long, designed for trim work and cabinetry with small heads for countersinking. Classified under HTS 7317.00.55.60 as other uncoated nails from round wire of one-piece construction. Conforms to chapter wire definition with dimensions under 16 mm.
Round Wire Siding Nails 2-1/2 Inch
2-1/2 inch round wire nails of one-piece steel construction for vinyl or wood siding installation, uncoated for clean finishes. HTS 7317.00.55.60 covers these as other non-coated round wire nails. Wire dimensions comply with chapter maximum.
Round Wire Underlayment Nails 1-1/4 Inch
1-1/4 inch ringless round wire nails of one-piece steel for securing floor underlayment, uncoated for subfloor applications. Classified HTS 7317.00.55.60 as other non-coated round wire construction. Chapter wire parameters met.
Round Wire Trim Nails 2 Inch
2-inch round wire trim nails constructed in one piece from steel for baseboards and crown molding, maintained uncoated. Falls under HTS 7317.00.55.60 as other round wire articles not plated/painted. Conforms to wire cross-section limit.
Round Wire Box Nails 1-1/4 Inch
Light-duty box nails made from one-piece round steel wire, 1-1/4 inches long with thinner shanks than common nails for packaging and light framing. HTS 7317.00.55.60 applies to these uncoated articles of round wire construction without plating or paint. Wire cross-section under 16 mm per chapter notes.