Nickel-Alloy Stainless Steel Coil Stock 350mm Wide
Cold-rolled coil stock of stainless steel, 350 mm wide, with 12% nickel by weight, supplied in master coils for slitting. Meets HTS 7220.20.10.15 criteria: flat-rolled stainless, <600 mm wide, >=300 mm wide, 0.5-24% Ni, not further worked. Used for automotive trim and hardware components.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If of rectangular cross-section (not strip)
Statistical suffix differentiates strip (10.15) from other rectangular flat-rolled shapes (10.10).
If hot-rolled rather than cold-rolled
Hot-rolled stainless flat products precede cold-rolled in tariff structure under 7219.
If width of 600 mm or more
Wider flat-rolled stainless bars/rods/plates shift to heading 7221.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Submit entry with weight percent nickel certification; U.S
• Note (a) definitions may apply for high-strength variants
• Document cold-rolling process to distinguish from hot-rolled (heading 7219) equivalents
• Check for inadvertent further working like oil coating, which could trigger 7220.40 classification
Related Products under HTS 7220.20.10.15
300 Series Cold-Rolled Stainless Steel Strip 430mm Wide
Cold-rolled flat-rolled stainless steel strip of 430 mm width, containing approximately 8-10% nickel and 18% chromium, not further worked beyond cold-reduction. It falls under HTS 7220.20.10.15 as a stainless steel product less than 600 mm wide, 300 mm or more in width, with nickel content between 0.5% and 24%. Commonly used in manufacturing kitchen utensils and decorative trim.
Stainless Steel Cold-Reduced Sheet 500mm Wide for Appliances
Cold-reduced stainless steel sheet measuring 500 mm in width, with 10% nickel content, used in appliance manufacturing. Classified under HTS 7220.20.10.15 due to stainless steel composition, width of 300 mm or more but under 600 mm, and lack of further working beyond cold-rolling. Ideal for refrigerator panels and oven liners.
AISI 304 Cold-Rolled Stainless Steel Banding 450mm Wide
AISI 304 grade cold-rolled stainless steel flat banding, 450 mm width, 8-10.5% nickel content, for industrial packaging strapping. HTS 7220.20.10.15 applies as cold-rolled stainless steel, width 300-600 mm, appropriate nickel range, no further surface treatments. Provides corrosion resistance for securing heavy loads.
Cold-Rolled 316L Stainless Steel Sheet 380mm Wide
Low-carbon 316L stainless steel cold-rolled sheet, 380 mm wide, with 10-14% nickel and molybdenum addition for pitting resistance. Fits HTS 7220.20.10.15: stainless flat-rolled, cold-reduced, 300+ mm <600 mm width, 0.5-24% Ni, not further worked. Suited for chemical processing equipment panels.
Duplex Stainless Steel Cold Band 550mm Wide
Cold-rolled duplex stainless steel band, 550 mm width, with 4-8% nickel balancing austenitic/ferritic structure for high strength. Under HTS 7220.20.10.15 for cold-rolled stainless flat products 300-600 mm wide, >0.5% <24% Ni, no further working. Used in oil & gas structural components.
Cold-Reduced Stainless Steel for Cookware Blanks 420mm Wide
Cold-reduced stainless steel blanks sized 420 mm wide, 12% nickel, supplied for deep drawing into pots and pans. HTS 7220.20.10.15 covers this not-further-worked cold-rolled stainless strip/sheet in the specified width and nickel range. Provides food-grade corrosion resistance.