AISI 316L Cold-Reduced Stainless Steel Coil 4mm Thick
AISI 316L low-carbon stainless steel coil, cold-reduced to 4 mm thickness with width over 1370 mm, free of additional coatings, polishing, or chemical treatments. Classified under HTS 7219.32.0025 for cold-rolled stainless steel coils in the 3-4.75 mm thickness range, wider than 1370 mm, other types.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If meets high-strength steel definition
If yield strength meets Chapter 72 note (a) criteria for high-strength steel, it shifts to the specific statistical suffix within the same subheading.
If clad with another metal
Cladding constitutes 'further worked' per Chapter note, moving to cladded products subheading.
If imported as tubular products
If formed into tubes/pipes before import, classifies under Chapter 73 for seamless stainless tubes rather than flat-rolled sheet.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Submit chemical analysis confirming molybdenum content for 316L grade; measure coil ID/OD precisely for customs verification; declare as 'not further worked' explicitly to avoid reclassification
Related Products under HTS 7219.32.00.25
AISI 304 Cold-Rolled Stainless Steel Coil 3.5mm Thick
This is a flat-rolled coil of AISI 304 austenitic stainless steel, cold-rolled to a thickness of 3.5 mm and width exceeding 1370 mm, not subjected to any further surface treatments beyond cold-rolling. It falls under HTS 7219.32.0025 as a stainless steel product of 3-4.75 mm thickness, in coils wider than 1370 mm, classified as 'other' not further worked than cold-rolled.
430 Ferritic Cold-Rolled Stainless Steel Coil 3.2mm
Ferritic grade 430 stainless steel flat-rolled coil, cold-rolled to 3.2 mm thick and over 1370 mm wide, without patterns, enameling, or other surface finishes. Fits HTS 7219.32.0025 as 'other' cold-rolled stainless coils of 3 mm+ thickness under 4.75 mm.
AISI 321 Cold-Rolled Stainless Coil 4.5mm Thick
Titanium-stabilized AISI 321 austenitic stainless steel coil, cold-rolled to 4.5 mm thickness, width >1370 mm, not further worked. HTS 7219.32.0025 applies to these precise dimensions for other stainless cold-rolled coils.
17-4PH Precipitation Hardening Stainless Coil 3.8mm
17-4PH martensitic precipitation hardening stainless steel cold-rolled coil, 3.8 mm thick, >1370 mm wide, untreated beyond cold-reduction. Meets HTS 7219.32.0025 criteria for thick, wide, other cold-rolled stainless coils.
Duplex 2205 Cold-Rolled Stainless Steel Coil 3.25mm
Duplex 2205 (UNS S31803) stainless steel coil cold-rolled to 3.25 mm, width exceeding 1370 mm, no additional working. HTS 7219.32.0025 covers this corrosion-resistant grade in the specified thickness and coil dimensions.
AISI 310 Cold-Rolled Heat-Resistant Stainless Coil 4.2mm
High-temperature AISI 310 stainless steel flat coil, cold-rolled 4.2 mm thick, >1370 mm wide, excluding further treatments. Although heat-resisting per note (g), classifies under general stainless HTS 7219.32.0025 for these specs.