Other
Flat-rolled products of stainless steel, of a width of 600 mm or more: > Not further worked than cold-rolled (cold-reduced): > Of a thickness of 3 mm or more but less than 4.75 mm > In coils: > Of a width of 1370 mm or more: > Other: > Other
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7219.32.00.25
AISI 304 Cold-Rolled Stainless Steel Coil 3.5mm Thick
This is a flat-rolled coil of AISI 304 austenitic stainless steel, cold-rolled to a thickness of 3.5 mm and width exceeding 1370 mm, not subjected to any further surface treatments beyond cold-rolling. It falls under HTS 7219.32.0025 as a stainless steel product of 3-4.75 mm thickness, in coils wider than 1370 mm, classified as 'other' not further worked than cold-rolled.
AISI 316L Cold-Reduced Stainless Steel Coil 4mm Thick
AISI 316L low-carbon stainless steel coil, cold-reduced to 4 mm thickness with width over 1370 mm, free of additional coatings, polishing, or chemical treatments. Classified under HTS 7219.32.0025 for cold-rolled stainless steel coils in the 3-4.75 mm thickness range, wider than 1370 mm, other types.
430 Ferritic Cold-Rolled Stainless Steel Coil 3.2mm
Ferritic grade 430 stainless steel flat-rolled coil, cold-rolled to 3.2 mm thick and over 1370 mm wide, without patterns, enameling, or other surface finishes. Fits HTS 7219.32.0025 as 'other' cold-rolled stainless coils of 3 mm+ thickness under 4.75 mm.
AISI 321 Cold-Rolled Stainless Coil 4.5mm Thick
Titanium-stabilized AISI 321 austenitic stainless steel coil, cold-rolled to 4.5 mm thickness, width >1370 mm, not further worked. HTS 7219.32.0025 applies to these precise dimensions for other stainless cold-rolled coils.
17-4PH Precipitation Hardening Stainless Coil 3.8mm
17-4PH martensitic precipitation hardening stainless steel cold-rolled coil, 3.8 mm thick, >1370 mm wide, untreated beyond cold-reduction. Meets HTS 7219.32.0025 criteria for thick, wide, other cold-rolled stainless coils.
Duplex 2205 Cold-Rolled Stainless Steel Coil 3.25mm
Duplex 2205 (UNS S31803) stainless steel coil cold-rolled to 3.25 mm, width exceeding 1370 mm, no additional working. HTS 7219.32.0025 covers this corrosion-resistant grade in the specified thickness and coil dimensions.
AISI 310 Cold-Rolled Heat-Resistant Stainless Coil 4.2mm
High-temperature AISI 310 stainless steel flat coil, cold-rolled 4.2 mm thick, >1370 mm wide, excluding further treatments. Although heat-resisting per note (g), classifies under general stainless HTS 7219.32.0025 for these specs.
409 Cold-Rolled Automotive Stainless Steel Coil 3.7mm
Grade 409 ferritic stainless coil for exhaust systems, cold-rolled to 3.7 mm, width >1370 mm, not further worked. HTS 7219.32.0025 designation for other cold-rolled stainless in this thickness/coil config.
AISI 304 Cold-Rolled Mill Edge Coil 3.9mm Thick
Mill edge AISI 304 stainless steel coil with natural edges, cold-rolled 3.9 mm thick, >1370 mm wide, no slitting or edge conditioning. Falls squarely in HTS 7219.32.0025 as other wide cold-rolled stainless coils.
316Ti Stabilized Stainless Cold Coil 4.4mm Thick
Titanium-stabilized 316Ti stainless steel cold-rolled coil, 4.4 mm thickness, width >1370 mm, minimal surface working only. HTS 7219.32.0025 captures these stabilized austenitic grades in the defined parameters.