Hot-Rolled Mild Steel Coil with Mill Edges 1.5mm Thick
This is a flat-rolled product of nonalloy steel, hot-rolled in coils, with a thickness of 1.5 mm and width exceeding 600 mm, featuring untrimmed mill edges directly from the rolling process. It falls under HTS 7208.39.0030 because it is not clad, plated, or coated, not further worked beyond hot-rolling, and specifically has untrimmed edges. Commonly used as feedstock for further processing into sheets or structural components.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness of 2 mm or more but less than 3 mm
Thicker hot-rolled coils in this category move to 7208.36, while sub-2mm stays in 7208.39
If cold-rolled after hot-rolling
Cold reduction or pickling changes it from hot-rolled to cold-rolled products in heading 7210
If width under 600 mm
Narrower hot-rolled strip falls outside the 600mm+ width requirement for 7208
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Verify thickness under 3 mm and untrimmed edges via mill certificates to avoid reclassification to trimmed edge subheadings
• Provide chemical composition analysis confirming nonalloy steel (max 10% alloying elements) for proper Chapter 72 classification
• Check for any unintended coatings or further working that could shift to 7210+ headings; document hot-rolled state at entry
Related Products under HTS 7208.39.00.30
HRPO Steel Coil Mill Edge 2.2mm
Hot-rolled pickled and oiled (HRPO) nonalloy steel coil with untrimmed edges, 2.2 mm thick and over 600 mm wide, supplied in coil form. Although pickled, it remains classified under hot-rolled not further worked per Chapter 72 notes, as pickling doesn't constitute 'further working.' The untrimmed mill edges distinguish it under HTS 7208.39.0030 for applications in automotive panels.
Nonalloy Steel Hot Band Coil 1.8mm Untrimmed
Hot band coil of nonalloy steel, 1.8 mm thickness, wide format (>600 mm), retaining rough mill edges from rolling. This semi-finished product is not further worked than hot-rolled and fits HTS 7208.39.0030 precisely due to untrimmed edges and specs. Ideal for slitting into narrower sheets for construction.
Mill Edge Low Carbon Steel Coil 2.0mm for Stamping
Low carbon nonalloy steel hot-rolled coil with mill edges, 2.0 mm thick, coil width 1000 mm, for press stamping applications. Untrimmed edges and lack of cladding/coating place it squarely in HTS 7208.39.0030 as hot-rolled, not further worked flat product.
Unpickled Hot-Rolled Steel Coil Mill Edge 1.2mm
Unpickled hot-rolled nonalloy steel coil showing scale, 1.2 mm thick with characteristic untrimmed mill edges, width 800 mm. The absence of pickling keeps surface as-rolled, fitting HTS 7208.39.0030 for thinnest hot-rolled coil category with untrimmed edges.
Drawing Quality Hot-Rolled Coil Mill Edge 1.9mm
Drawing quality (DQ) nonalloy steel hot-rolled in coil form, 1.9 mm gauge, untrimmed edges, suitable for deep drawing operations. Meets all criteria for HTS 7208.39.0030: hot-rolled, not further worked, <3 mm thick, wide coil with mill edges.
Commercial Quality HR Steel Coil Untrimmed 2.5mm
Commercial quality hot-rolled nonalloy steel coil, 2.5 mm thick, featuring authentic mill edges, coil width 1500 mm. Classified under HTS 7208.39.0030 for its unprocessed hot-rolled state, no cladding or further surface treatments.