Other

4407.22.00Virola, Imbuia and Balsa

4407.23Teak

4407.25.00Dark Red Meranti, Light Red Meranti and Meranti Bakau

4407.26.00White Lauan, White Meranti, White Seraya, Yellow Meranti and Alan

Calculate exact duty for your shipment Not sure about classification? Ask the Tariff Assistant

Products classified under Tariff item 4407.2

End-Jointed Mahogany Finger-Joint Blocks 12mm Thick

End-jointed mahogany finger-joint blocks, 12 mm thick, made from Swietenia spp. and assembled via finger-jointing, then sanded. They are sawn lengthwise and exceed 6 mm in thickness, qualifying as wood of heading 44.07, and are classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Mahogany Stair Tread Blanks Sawn Lengthwise

Pre-cut mahogany stair tread blanks, sawn lengthwise from Swietenia spp., over 6 mm thick, and planed on top and bottom. These are unfinished sawn wood products for architectural millwork, falling under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Planed Mahogany Drawer Sides 19mm Thick

Sawn and planed mahogany drawer sides, 19 mm thick, made from Swietenia spp., exceeding 6 mm thickness. These are unfinished lumber components for custom furniture, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Planed Mahogany (Swietenia mahagoni) Boards 8mm Thick

End-jointed and sanded boards from Cuban mahogany (Swietenia mahagoni), 8 mm thick, sawn lengthwise for fine joinery. These boards exceed 6 mm in thickness and are classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Quarter-Sawn Mahogany Lumber for Boat Building

Quarter-sawn Swietenia macrophylla planks exceeding 6 mm, planed for marine applications with high rot resistance. These are sawn lengthwise and classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Sanded Ribbon Grain Mahogany for Cabinet Doors

Ribbon figure mahogany (Swietenia macrophylla) sawn and sanded to 10 mm thickness for raised panel doors. These are unfinished sawn wood products, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Sawn Genuine Mahogany Lumber (Swietenia macrophylla)

Sawn genuine mahogany lumber from Swietenia macrophylla, thickness exceeding 6 mm, typically planed and sanded for woodworking. This is standard sawn tropical wood, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Sawn Mahogany Architrave Moulding Blanks

Lengthwise sawn Swietenia spp. trim blanks over 6 mm thick, sanded for colonial moulding profiles. These are unfinished sawn wood products, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Sliced Mahogany Flitch for Veneer Preparation

Lengthwise sliced Swietenia spp. flitches over 6 mm thick, lightly sanded but not reduced to thin veneer sheets. These are sawn or sliced wood products, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Swietenia Sawn Lumber for Guitar Neck Blanks

Quartersawn mahogany neck blanks from Swietenia spp., 25 mm thick, sanded for luthiers. These are sawn wood products exceeding 6 mm, classifiable under tariff item 4407.21.00 as mahogany (Swietenia spp.).

Balsa Core Sawn Panels 15mm

Sawn Balsa panels, 15mm thick, for composite sandwich core construction in marine and wind energy applications. These panels are end-jointed and exceed 6mm thickness, qualifying under tariff item 4407.22.00 for tropical wood sawn lengthwise.

Balsa End-Grain Sawn Blocks

Balsa wood sawn into end-grain blocks, 20mm thick, for butcher block-style surfaces and modeling bases. These blocks are end-jointed and exceed 6mm thickness, meeting the criteria for tropical wood under tariff item 4407.22.00.

Balsa End-Jointed Lumber Strips

End-jointed balsa wood strips sawn lengthwise, sanded, 12 mm thick, for pattern-making and core stock. These strips are classified under tariff item 4407.22.00 as end-jointed tropical sawn balsa exceeding 6 mm in thickness, allowing length extension via finger joints.

Balsa End-Jointed Stringers

End-jointed Balsa stringers sawn to 25mm for wind turbine spar cores and aerospace doublers. These stringers are precision sanded and exceed 6mm thickness, qualifying under tariff item 4407.22.00 for tropical wood.

Balsa Sawn Guitar Soundboards

Specially sawn balsa wood blanks for acoustic guitar soundboards, bookmatched pairs, 4 mm thickness. Although the thickness is less than 6 mm, these blanks are classified under tariff item 4407.22.00 as sawn tropical balsa, as the heading allows for musical instrument components.

Balsa Sawn Planks 1x12

Balsa (Ochroma pyramidale) wood sawn into 1x12 wide planks, lightly sanded, thickness exceeding 6 mm. These planks are used for model-making and core materials and are classified under tariff item 4407.22.00 as 'other' tropical sawn wood, differentiated from unsawn wood.

Balsa Sliced Contour Panels

Pre-contoured Balsa panels sliced to 10mm for surfboard blanks and radome construction. These panels are sanded and exceed 6mm thickness, meeting the criteria for tropical wood under tariff item 4407.22.00.

Balsa Wood Blocks for Surfboard Cores 12x12x2 inch

Rough-sawn balsa blocks measuring 12x12x2 inches, sourced from Ochroma lagopus, planed on two sides with a thickness of 50.8 mm. These blocks are intended for surfboard core lamination and qualify under tariff item 4407.22.00 as tropical wood sawn lengthwise, exceeding 6 mm in thickness.

Balsa Wood Core Sheets for Marine Composites

Balsa core sheets 4x8 feet, 1 inch thick, planed and sanded, from tropical balsa (Ochroma lagopus). These sheets are used in marine composite sandwich construction for boat hulls and fall under tariff item 4407.22.00 as sawn tropical wood exceeding 6 mm in thickness.

Balsa Wood for Model Boat Kits 3/8 inch Thick

Planed balsa sheets 3/8 inch (9.5 mm) thick, cut to pattern for model boat hulls, from Ochroma lagopus. These sheets are sawn or peeled tropical wood exceeding 6 mm in thickness and are classified under tariff item 4407.22.00, as they are not yet assembled into a finished article.

Balsa Wood Sliced Sheets 10mm

Lightweight Balsa wood sliced to 10mm thickness for model making, aerospace cores, and insulation panels. These sheets are end-jointed for stability and exceed 6mm thickness, qualifying under tariff item 4407.22.00.

End-Jointed Balsa Wood Strips 1/2x1/2 inch

End-jointed balsa strips with a 1/2 x 1/2 inch cross-section, 36 inches long, from tropical balsa (Ochroma lagopus), thickness exceeding 6 mm. These strips are sawn lengthwise and finger-jointed, qualifying under tariff item 4407.22.00 for end-jointed tropical balsa wood.

End-Jointed Virola Sawn Boards

Virola lumber boards sawn lengthwise, end-jointed, and sanded to 12mm thickness for stable construction use. These boards are used in boat building and qualify under tariff item 4407.22.00 for tropical wood.

Imbuia Live Edge Sawn Slabs

Live-edge Imbuia slabs sawn lengthwise from tropical logs, lightly planed faces, 25 mm+ thickness for tabletops. These slabs are classified under tariff item 4407.22.00 as figured tropical Imbuia sawn wood exceeding veneer thickness, with natural edges preserved.

Imbuia Planed Boards for Guitar Backs

Planed Imbuia boards 8mm thick, quartered for musical instrument backs and sides. These boards are sawn and planed, exceeding 6mm thickness, and qualify under tariff item 4407.22.00 for tropical wood.

Imbuia Quarter-Sawn Boards

Quarter-sawn Imbuia lumber boards cut radially to minimize warping, sanded surface, 8/4 thickness for high-end furniture. These boards are classified under tariff item 4407.22.00 as other sawn tropical Imbuia wood exceeding 6 mm thick, sawn lengthwise per chapter notes.

Imbuia Sawn Boards 2x4

Imbuia (Phoebe porosa) tropical hardwood sawn lengthwise into 2x4 dimensional lumber, end-jointed for stability, with a thickness exceeding 6 mm. This product falls under tariff item 4407.22.00 as Virola, Imbuia, and Balsa sawn wood, meeting the chapter's definition of wood sawn or chipped lengthwise.

Imbuia Sawn Flitch for Veneer Matching

Imbuia flitch sawn to 12mm thickness for subsequent veneer slicing, maintaining book-matched patterns. This flitch qualifies under tariff item 4407.22.00 as sawn tropical wood exceeding 6mm.

Imbuia Sawn Stair Treads

Imbuia sawn stair treads planed to 8mm thickness with bullnosed edges for luxury staircases. These treads exceed 6mm thickness and qualify under tariff item 4407.22.00 for tropical wood.

Kiln-Dried Balsa Framing Lumber 2x4

Kiln-dried balsa framing lumber in 2x4 dimensions, 10 feet long, from Ochroma lagopus, sanded and planed. This tropical wood is sawn lengthwise, exceeding 6 mm in thickness, and falls under tariff item 4407.22.00 for lightweight framing applications.

Planed Balsa Wood Sheets 1/4 inch Thick

Planed balsa wood panels measuring 24x36 inches and 1/4 inch (6.35 mm) thick, sourced from Ochroma lagopus. These panels are sawn or sliced tropical balsa exceeding 6 mm in thickness, classified under tariff item 4407.22.00 with basic planing allowed.

Planed Imbuia Sawn Timber Panels

Imbuia wood sliced lengthwise and planed to over 6mm thickness for high-end joinery and musical instruments. This product is sanded for fine finishing and qualifies under tariff item 4407.22.00.

Planed Virola S4S Lumber

Virola tropical wood surfaced on four sides (S4S) sawn lumber, end-jointed, with a thickness of 19 mm, intended for interior trim applications. This product qualifies under tariff item 4407.22.00 as Virola sawn wood exceeding 6 mm in thickness, even when planed or sanded.

Precision-Sanded Balsa Leading Edges for Gliders

Precision-sanded balsa strips shaped to airfoil profiles for glider leading edges, 12 mm thick, from Ochroma lagopus. These strips are sawn tropical balsa exceeding 6 mm in thickness, with basic sanding allowed, and are classified under tariff item 4407.22.00.

Sanded Balsa Wood Planks for RC Aircraft

Sanded balsa planks with 2x6 inch cross-sections, 4 feet long, from Ochroma lagopus, thickness over 6 mm. These planks are used in radio-controlled model aircraft construction and are classified under tariff item 4407.22.00 as tropical balsa sawn lengthwise.

Sanded Imbuia S4S Lumber

Imbuia tropical hardwood surfaced four sides (S4S) to 1-inch thickness for premium millwork. This lumber is sawn lengthwise, planed, and sanded, exceeding 6mm thickness, and qualifies under tariff item 4407.22.00.

Sawn Balsa Wood Lumber 1x4x8 ft

Kiln-dried balsa wood boards sawn lengthwise to 1 inch thick, 4 inches wide, and 8 feet long, exceeding 6 mm thickness. These boards are planed and classified under tariff item 4407.22.00 as balsa (Ochroma lagopus), a tropical wood.

Sawn Virola Lumber 1x6

Virola wood sawn lengthwise into 1-inch by 6-inch boards, planed and sanded for smoothness, with a thickness exceeding 6 mm. This product is classified under tariff item 4407.22.00 as Virola sawn tropical wood, as planing and sanding do not alter its essential character.

Sawn Virola Lumber 8mm Thick

Virola wood sawn lengthwise to 8mm thickness for furniture and cabinetry. This lightweight, workable wood exceeds 6mm thickness and qualifies under tariff item 4407.22.00 for tropical wood.

Sliced Balsa Wood Panels for Wind Turbine Blades

Sliced balsa panels measuring 1 meter x 2 meter x 20 mm thick, from tropical Ochroma lagopus. These panels are used in wind turbine blade cores and are classified under tariff item 4407.22.00 as sawn or peeled tropical balsa exceeding 6 mm in thickness.

Virola Mixed Width Sawn Lumber

Random width Virola sawn lumber from tropical plantations, planed to a thickness of 1-1/4 inches, intended for millwork applications. This product falls under tariff item 4407.22.00 as Virola sawn wood exceeding 6 mm in thickness, with planing allowed per the heading's terms.

Virola Planed Decking Boards

Planed Virola decking boards 1-1/8 inch thick with eased edges for outdoor applications. These boards exceed 6mm thickness and qualify under tariff item 4407.22.00 for tropical wood.

Virola S4S Trim Boards

S4S Virola trim boards at 3/4-inch thickness for interior molding and trim. These boards are planed and sanded, exceeding 6mm thickness, and qualify under tariff item 4407.22.00.

Virola Sanded Dimension Lumber

Sanded Virola 2x6 dimension lumber sawn lengthwise for framing and sheathing, with a thickness of 38 mm. This product is classified under tariff item 4407.22.00 as Virola sawn tropical wood, as sanding does not change its classification under the chapter.

Virola Sliced Lumber for Cabinetry

Virola wood sliced to 9mm for cabinet doors and face frames, offering a cost-effective tropical alternative to mahogany. This product is sanded and exceeds 6mm thickness, qualifying under tariff item 4407.22.00.

End-Jointed Teak Studs

End-jointed teak studs sawn lengthwise and planed to a 2x6 profile, exceeding 6 mm in thickness, for structural outdoor use. The end-jointing and planing are permitted operations under this tariff item, which covers teak wood sawn or chipped lengthwise, whether or not planed, sanded or end-jointed.

Planed Teak Joists

Planed teak joists sawn lengthwise to a uniform 2x10 size, exceeding 6 mm in thickness, for flooring supports. The planing is a permitted surface treatment under this tariff item, which includes teak wood sawn lengthwise, whether or not planed.

Planed Teak Planks 2x4

Rough sawn teak converted to planed 2x4 dimensional lumber over 6 mm thick, end-jointed for stability. This product meets the tariff item's scope of teak wood sawn lengthwise, planed and end-jointed, with no further manufacturing that would change its character.

Sanded Teak Deck Boards

Teak boards sawn to 1x4 dimensions, sanded for decking applications, with a thickness of 25 mm exceeding the 6 mm limit. Sanding is a permitted surface operation under this tariff item, which covers teak wood sawn lengthwise, whether or not sanded.

Sanded Teak Fascia Boards

Teak fascia boards sanded smooth, sawn to a 1x8 profile over 6 mm for roof trim. The sanding and sawing are within the scope of this tariff item, which covers teak wood sawn lengthwise, whether or not sanded, for use as lumber.

Sawn Teak Lumber 1x6

Teak wood sawn lengthwise into 1-inch thick by 6-inch wide boards exceeding 6 mm thickness, typically planed and sanded for a smooth finish. This product falls under the tariff item as teak wood sawn lengthwise, with planing and sanding as permitted operations.

Sliced Teak Panel Stock

Teak sliced into large panels exceeding 6 mm thickness, sanded for cabinetry blanks. Slicing is an alternative to sawing and is explicitly covered by this tariff item, which includes teak wood sliced or peeled, whether or not sanded.

Teak Sawn Beams 4x8

Large teak beams sawn to 4x8 dimensions, lightly planed, over 6 mm thick for heavy construction. This product is classified under the tariff item as teak wood sawn lengthwise, with planing as a permitted surface treatment.

Teak Sawn Posts 6x6

Square sawn teak 6x6 posts planed, exceeding 6 mm for fencing and pergolas. This product falls under the tariff item as teak wood sawn lengthwise, planed, with no further manufacturing that would change its character as lumber.

Teak Sawn Railings

Sawn teak balustrade components exceeding 6 mm, planed for porch railings. These components are classified under the tariff item as teak wood sawn lengthwise, planed, before any assembly into railings.

Dark Red Meranti Construction Beams 50mm

Heavy sawn Dark Red Meranti beams, planed and end-jointed, exceeding 6 mm in thickness, used for structural framing in tropical architecture. This product falls under tariff item 4407.25.00 as it is wood sawn lengthwise of a named tropical species, Dark Red Meranti, and is not further worked beyond planing, sanding, or end-jointing.

Dark Red Meranti Sawn Door Stiles 35mm

Sawn Dark Red Meranti stiles for door frames, sanded and exceeding 6 mm in thickness. These are wood sawn lengthwise of a named tropical species, Dark Red Meranti, and are not further worked beyond sanding, fitting the scope of tariff item 4407.25.00.

Dark Red Meranti Sawn Moulding Blanks 15mm

Sawn blanks of Dark Red Meranti for custom mouldings, planed and exceeding 6 mm in thickness. These are unfinished sawn tropical wood of a named species, Dark Red Meranti, and are not yet shaped into mouldings, so they fall under tariff item 4407.25.00.

Dark Red Meranti Veneer Core Lumber 8mm

Thin sawn Dark Red Meranti lumber over 6 mm thick, used as core stock for laminated panels. This product is wood sawn lengthwise of a named tropical species, Dark Red Meranti, and is not further worked beyond sawing, fitting tariff item 4407.25.00.