18-Gauge 2-Inch Brad Nails in Wire Strip Collated Pack
These collated brad nails are made from round steel wire, one-piece construction, assembled in a wire strip for use in pneumatic brad nailers. They feature small brad heads and are designed for finish carpentry and trim work. Classified under HTS 7317.00.55.11 due to their round wire construction and wire strip collation.
Import Duty Rates by Country of Origin
| Origin Country | MFN Rate | Ch.99 Surcharges | Total Effective Rate |
|---|---|---|---|
| šØš³China | Free | +35.0% | 35% |
| š²š½Mexico | Free | +10.0% | 10% |
| šØš¦Canada | Free | +10.0% | 10% |
| š©šŖGermany | Free | +10.0% | 10% |
| šÆšµJapan | Free | +10.0% | 10% |
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If made of flat wire instead of round
Flat wire collated nails fall under a separate subheading, changing from round wire category.
If collated in plastic strips rather than wire
Plastic collated nails are classified differently from wire strip assemblies.
If imported loose/uncollated
Loose round wire nails without strip assembly move to heading 7318 for individual articles.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
ā¢ Verify wire diameter does not exceed 16 mm per Chapter 73 note and confirm round wire construction for 7317.00.55.11 classification
ā¢ Include detailed packing lists specifying collation type (wire strip) and nail specs to avoid reclassification as loose nails
ā¢ Ensure country-of-melt documentation for steel to comply with Section 232 tariffs if applicable
Related Products under HTS 7317.00.55.11
16-Gauge 2-1/2 Inch Finish Nails Wire Collated Strip
Medium gauge finish nails constructed from one-piece round steel wire, assembled in wire strips compatible with 16-gauge finish nailers. Ideal for baseboards, door casings, and cabinetry installation. HTS 7317.00.55.11 applies as they meet the round wire, one-piece, wire strip collated criteria.
15-Gauge 2-1/2 Inch Angled Finish Nails Wire Strip
15-gauge angled finish nails made from round wire, one-piece design, collated in wire strips for DA (dual angle) nailers used in woodworking. The angled collation allows access to tight corners. Falls under 7317.00.55.11 for round wire strip-collated nails.
21-Gauge 1-1/4 Inch Pin Nails Wire Collated Strip
Ultra-fine 21-gauge pin nails from round steel wire, headless or micro-head, assembled in straight wire strips for pin nailers in delicate trim and molding. Minimal surface damage makes them ideal for high-end furniture. HTS 7317.00.55.11 due to wire strip assembly from round wire.
18-Gauge 1-1/4 Inch Galvanized Brad Nails Wire Strip
Galvanized 18-gauge brad nails made of round wire, one-piece construction, collated in wire strips for corrosion resistance in exterior trim applications. The zinc coating protects against rust in humid environments. Classified HTS 7317.00.55.11 as round wire strip nails.
16-Gauge 1-1/2 Inch Bright Finish Nails Wire Collated
Bright (uncoated) 16-gauge finish nails from round steel wire, assembled in wire strips for interior finish work where galvanizing isn't needed. Common in furniture assembly and interior trim. HTS 7317.00.55.11 for one-piece round wire strip collated.
20-Gauge 3/4 Inch Micro Pin Nails Wire Strip Pack
Micro 20-gauge pin nails constructed from thin round wire, one-piece, collated in wire strips for ultra-delicate applications like picture frame molding and model building. Headless design leaves no visible marks. Under HTS 7317.00.55.11 as round wire collated nails.