Containing 8 percent or more but less than 24 percent by weight of nickel
Other bars and rods of stainless steel; angles, shapes and sections of stainless steel: > Bars and rods, not further worked than cold-formed or cold-finished > Other: > Of a circular cross-section: > With a maximum circular cross-sectional dimension of less than 18 mm: > Containing 8 percent or more but less than 24 percent by weight of nickel
Duty Rate (from China)
Except for products described in headings 9903.03.02–9903.03.11, articles the product of any country, as provided for in subdivision (aa) of U.S. note 2 to this subchapter
Effective with respect to entries on or after September 27, 2024, articles the product of China, as provided for in subdivision (b) of U.S. note 31 to this subchapter
Products classified under HTS 7222.20.00.43
Cold-Finished 316 Stainless Steel Round Bar 12mm
A cold-finished round bar made from 316 stainless steel alloy containing approximately 10-14% nickel by weight, with a circular cross-section of 12 mm diameter, less than 18 mm. Classified under HTS 7222.20.0043 as a stainless steel bar not further worked beyond cold-finishing, specifically for alloys with 8-24% nickel content. Used in marine and chemical processing applications due to its corrosion resistance.
17-4 PH Stainless Steel Cold-Drawn Rod 14mm
Cold-drawn round rod of 17-4 PH precipitation hardening stainless steel with 14-16% nickel content, 14 mm diameter circular cross-section. Fits HTS 7222.20.0043 for cold-formed stainless bars under 18 mm with 8-24% nickel, not further worked. Ideal for aerospace fasteners requiring high strength and corrosion resistance.
Nitronic 50 Stainless Steel Bar 10mm Diameter
Cold-finished round bar of Nitronic 50 (XM-19) stainless steel containing about 12% nickel, with 10 mm circular cross-section under 18 mm limit. Matches HTS 7222.20.0043 for stainless bars cold-formed, 8-<24% nickel, used in high-stress valve stems and pump shafts.
Custom 15-5 PH Stainless Round Rod 16mm
Cold-formed 15-5 PH stainless steel round rod with 15% nickel content, 16 mm diameter (under 18 mm max). HTS 7222.20.0043 applies to this cold-finished stainless bar of intermediate nickel alloy for aircraft structural components.
AL-6XN Stainless Steel Cold Bar 9mm
Cold-finished AL-6XN super-austenitic stainless round bar with 20-22% nickel, 9 mm circular cross-section. Perfect fit for HTS 7222.20.0043: stainless bars <18 mm diameter, 8-<24% Ni, for severe corrosive environments like desalination plants.
321 Stainless Steel Cold-Rolled Rod 11mm
Cold-rolled 321 stabilized stainless steel round rod containing 9-12% nickel, 11 mm diameter under 18 mm. HTS 7222.20.0043 covers this cold-finished bar for high-temperature exhaust systems and weld decay resistance.
310S Stainless Steel Bright Bar 15mm
'Bright' cold-drawn 310S heat-resistant stainless bar with 19-22% nickel, 15 mm round section. Classifies in HTS 7222.20.0043 as cold-finished stainless <18 mm, 8-24% Ni, for furnace parts (note: bright finish typically not 'further worked' unless polished).
904L Stainless Steel Cold Bar 13mm Dia
Cold-finished 904L super-austenitic stainless round bar with 23-25% nickel (qualifies at lower end), 13 mm diameter. HTS 7222.20.0043 for <18 mm circular cold stainless bars 8-<24% Ni; used in chemical/pharma processing.