Incoloy 800 Cold-Rolled Alloy Steel Sheet
Flat-rolled stainless steel sheet made from Incoloy 800, a high-nickel alloy steel with over 30% nickel content, cold-rolled to a thickness exceeding 1.25 mm and width under 300 mm. This product is not further worked beyond cold-rolling, fitting HTS 7220.20.60.05 due to its high-nickel composition and precise dimensions. Used in chemical processing equipment for corrosion resistance.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness of 0.5 mm or more but not exceeding 1.25 mm
Thinner cold-rolled high-nickel sheets shift to the adjacent thickness subheading within the same width category.
If width of 600 mm or more
Wider flat-rolled stainless steel products fall under Chapter 72 heading 7219 for broader width ranges.
If supplied in bars or rods rather than flat-rolled
High-nickel stainless products in bar form are classified under heading 7222 for non-flat shapes.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Certify nickel content exceeds 24% with mill test reports to confirm high-nickel alloy steel classification
• Verify cold-rolled status without further working like polishing to avoid reclassification under 7220.40 subheadings
• Check for Section 232 tariffs on steel; provide documentation proving non-Chinese origin if applicable
Related Products under HTS 7220.20.60.05
Hastelloy C-276 Cold-Reduced Steel Strip
Cold-reduced strip of Hastelloy C-276, a nickel-molybdenum-chromium high-nickel alloy steel (>50% nickel), with thickness over 1.25 mm and width less than 300 mm, not further worked. Classified under HTS 7220.20.60.05 for its high-nickel alloy properties and cold-rolling process only. Ideal for aerospace and marine applications requiring extreme corrosion resistance.
Alloy 625 Cold-Rolled Stainless Steel Plate
Cold-rolled plate from Alloy 625 (Inconel 625), high-nickel alloy steel with ~58% nickel, thickness exceeding 1.25 mm, width under 300 mm, without further working. Meets HTS 7220.20.60.05 criteria for high-nickel stainless flat products narrowly dimensioned. Commonly used in nuclear reactors and gas turbines.
Monel 400 Cold-Rolled High-Nickel Steel Sheet
Cold-rolled sheet of Monel 400 alloy (67% nickel-copper stainless steel), thickness >1.25 mm, width <300 mm, not further worked than cold-rolled. Fits HTS 7220.20.60.05 as high-nickel alloy steel flat-rolled product. Applied in marine engineering and hydrocarbon processing.
Inconel 718 Cold-Reduced Alloy Strip
Cold-reduced strip from Inconel 718, precipitation-hardenable high-nickel alloy steel (~52% nickel), >1.25 mm thick, <300 mm wide, no further working. Precisely matches HTS 7220.20.60.05 for cold-rolled high-nickel stainless flats. Used in jet engine components.
Nickel 200 Cold-Rolled Stainless Steel Foil Alternative
Note: Though typically thinner, select thicker Nickel 200 (99% nickel alloy steel) cold-rolled sheets >1.25 mm thick, <300 mm wide for high-nickel classification under HTS 7220.20.60.05, not further worked. Used in electronics and chemical lining where purity is critical.
Custom 625-Modified High-Nickel Cold Strip
Cold-rolled strip of Custom Age 625 PLUS (high-nickel stainless >50% Ni), thickness exceeding 1.25 mm, width <300 mm, limited to cold-reduction. HTS 7220.20.60.05 applies due to high-nickel alloy steel definition and dimensional specs. For sour gas service in oil & gas.