317 Stainless Steel Hot-Rolled Wide Plate 7mm
Type 317 stainless hot-rolled plate with 11-14% nickel, 3-4% molybdenum, exceeding 1880 mm width and 7 mm thick, not in coils. Directly classifiable in HTS 7219.22.0025 for its hot-rolled state and precise elemental composition, suited for pulp and paper industry.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If width ≤1880 mm
Narrower widths within same thickness/alloy fall under the parallel subheading for ≤1880 mm.
If <0.5% nickel
Lack of significant nickel excludes from Ni-specified subheadings, going to general stainless.
If in coils and further worked (e.g., annealed)
Coiled and any surface treatment beyond hot-rolling shifts to 7220 series for stainless coil products.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Label entries clearly with alloy grade and dimensions to facilitate CBP review for this specific subheading
• Ensure no nonmetallic coatings; even paint qualifies as further worked per Chapter definitions
Related Products under HTS 7219.22.00.25
Custom 317LMN Hot-Rolled Stainless Mill Plate
317LMN low-carbon/manganese/nitrogen enhanced stainless hot-rolled plate, 13.5% Ni, 4.2% Mo, ultra-wide >1880 mm, 10 mm max thick, hot-rolled only. HTS 7219.22.0025 due to alloy matching Ni/Mo specs for urea plant construction.
Type 316 Hot-Rolled Stainless Steel Plate 6mm Thick
Hot-rolled stainless steel plate of Type 316 composition, featuring 16-18% chromium, 10-14% nickel (>0.5%), and 2-3% molybdenum, with width over 1880 mm and thickness between 4.75-10 mm. Classified under HTS 7219.22.0025 as a flat-rolled product not further worked than hot-rolled, not in coils, due to its specific alloy content and dimensions. Used in chemical processing equipment for corrosion resistance.
316L Hot-Rolled Stainless Steel Slab 8mm Thick Wide
Type 316L low-carbon stainless steel hot-rolled plate, 12-15% nickel and 2-3% molybdenum, produced in widths exceeding 1880 mm and 8 mm thickness, not in coils or further worked. Fits HTS 7219.22.0025 precisely due to alloy specs and hot-rolled state, ideal for marine applications requiring pitting resistance.
Duplex 2205 Hot-Rolled Stainless Plate 5mm Thick
Duplex 2205 (UNS S31803) stainless steel hot-rolled plate with ~5% nickel and 3% molybdenum, width over 1880 mm, thickness 5 mm, not coiled or further processed. Meets HTS 7219.22.0025 criteria for Ni and Mo content in hot-rolled, wide flat products used in oil & gas platforms.
AL-6XN Hot-Rolled Stainless Steel Sheet 9mm Thick
AL-6XN super-austenitic stainless hot-rolled plate, 20-22% nickel but 2.5% molybdenum limit fits, width >1880 mm, 9 mm thick, not further worked. HTS 7219.22.0025 applies due to Mo range 1.5-5% and hot-rolled flat form for severe corrosion environments.
Type 316H Hot-Rolled Wide Stainless Plate 4.8mm
High-carbon Type 316H stainless steel hot-rolled, 11-14% Ni, 2-3% Mo, >1880 mm wide, exactly 4.8 mm thick (min for subheading), uncoiled. Classed in HTS 7219.22.0025 for elevated temperature applications in power generation.