Type 304 Hot-Rolled Stainless Steel Coil 10mm Thick 1750mm Wide
Standard Type 304 austenitic stainless hot-rolled coil at maximum 10 mm thickness, 1750 mm wide, in coil. Classifies under HTS 7219.12.0056 for upper end of thickness range and extra width. For general heavy plate fabrication.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness exceeds 10 mm
Over 10 mm hot-rolled stainless moves to next subheading.
If carbon steel equivalent
Non-stainless hot-rolled coils over 10 mm thick classify under 7208.
If clad with other metal
Cladding treatment qualifies as further worked per Chapter definition.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Exact thickness gauging critical at 10 mm boundary to avoid 7219.14 spillover
• Mill certificates mandatory for alloy content and hot-rolling confirmation
• Watch for partial rust; no duty allowance per Chapter note
Related Products under HTS 7219.12.00.56
Type 304 Hot-Rolled Stainless Steel Coil 5mm Thick 1600mm Wide
Hot-rolled stainless steel coil made from AISI Type 304 alloy, measuring 5 mm thick and 1600 mm wide, supplied in coil form without further surface working. Classified under HTS 7219.12.0056 due to its stainless steel composition, hot-rolled state, thickness between 4.75-10 mm, and width exceeding 1575 mm. Used primarily for heavy-duty fabrication like chemical processing tanks.
Type 316L Hot-Rolled Stainless Steel Coil 6mm Thick 1650mm Wide
Hot-rolled coil of low-carbon Type 316L stainless steel (16% Cr, 10% Ni, 2% Mo), 6 mm thick and 1650 mm wide, in coil form without additional processing. Fits HTS 7219.12.0056 for hot-rolled stainless steel over 4.75 mm thick, width >1575 mm. Ideal for marine and pharmaceutical equipment due to corrosion resistance.
Duplex 2205 Hot-Rolled Stainless Steel Coil 8mm Thick 1700mm Wide
Hot-rolled duplex stainless steel 2205 grade coil (22% Cr, 5% Ni, 3% Mo), 8 mm thickness, 1700 mm width, uncoated and in coil. Matches HTS 7219.12.0056 specs for stainless flat-rolled products hot-rolled, 4.75-10 mm thick, >1575 mm wide. Suited for offshore platforms and pressure vessels.
Type 310 Hot-Rolled Stainless Steel Coil 4.8mm Thick 1580mm Wide
High-temperature Type 310 stainless steel hot-rolled coil, 4.8 mm thick, 1580 mm wide, in coil without further working. HTS 7219.12.0056 applies to its stainless nature, precise thickness range, and extra-wide dimension. Used in furnace parts and heat exchangers.
Type 321 Hot-Rolled Stainless Steel Coil 7mm Thick 1620mm Wide
Stabilized Type 321 stainless (titanium-added 304 variant) hot-rolled coil, 7 mm thick, 1620 mm wide, hot-rolled only. Precisely fits HTS 7219.12.0056 for wide stainless coils 4.75-10 mm thick. Applied in welded structures prone to intergranular corrosion.
17-4 PH Precipitation Hardening Stainless Coil 9mm Thick 1800mm Wide
17-4 PH martensitic precipitation hardening stainless steel hot-rolled coil, 9 mm thick, 1800 mm wide, in coil form. HTS 7219.12.0056 due to stainless classification, hot-rolled, thickness, and width exceeding 1575 mm. For aerospace and high-strength structural uses.