A619 Annealed Cold-Rolled Steel Coil 1.0mm x 1524mm
ASTM A619 drawing quality cold-rolled steel coil, fully annealed, 1.0 mm thickness, 1524 mm width, in coils without further surface working. Classified in HTS 7209.17.00.70 for its nonalloy steel, cold-rolled, annealed characteristics in the specified thickness. Primarily for deep drawing applications like cans and pans.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If razor blade steel specs
Specific stainless razor blade steel dimensions/composition uses dedicated subheading.
If temper rolled post-annealing
Additional skin-pass temper rolling may classify as 'further worked' in 7211.
If hot-rolled pickle & oiled base
Pre-cold-rolled hot-rolled products in coils remain in 7208 if not cold-reduced.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• ASTM A619 certification required; mismatch in grade could lead to commercial vs drawing quality reclassification
• Verify no chemical treatments (phosphating etc.) as these constitute 'further worked' per Chapter notes
• Thickness tolerance must be within spec; ultrasonic gauging docs prevent disputes
Related Products under HTS 7209.17.00.70
SPCC Annealed Cold-Rolled Steel Coil 0.8mm x 1219mm
This is a standard commercial quality (SPCC) cold-rolled steel coil that has been annealed to restore ductility after cold reduction, with thickness of 0.8 mm and width of 1219 mm in coil form. It falls under HTS 7209.17.00.70 as a flat-rolled product of nonalloy steel, cold-rolled, not further worked than cold-rolled, 0.5-1 mm thick, and specifically annealed. Commonly used for appliance housings and metal furniture.
DC01 Annealed Cold-Rolled Steel Coil 0.7mm x 1500mm
EN 10130 DC01 grade cold-rolled steel coil, annealed for improved formability, 0.7 mm thick and 1500 mm wide, in coil form without plating or cladding. Classified under HTS 7209.17.00.70 due to its nonalloy composition, cold-rolled state, specified thickness range, and annealing treatment. Ideal for automotive inner panels and tubing.
Annealed CR2 Cold-Rolled Steel Coil 0.9mm x 1000mm
Commercial quality CR2 grade cold-rolled steel coil that is annealed, 0.9 mm thickness, 1000 mm width, in coils and not further worked beyond cold-rolling and annealing. HTS 7209.17.00.70 applies as it matches the exact criteria for nonalloy, cold-rolled, annealed coils in the 0.5-1 mm thickness range. Used in manufacturing of shelves and enclosures.
SPHC Annealed Cold-Rolled Steel Coil 0.6mm x 1250mm
Low carbon SPHC grade cold-rolled steel coil, batch annealed for softness, 0.6 mm thick by 1250 mm wide in coil form, unclad and uncoated. Fits HTS 7209.17.00.70 precisely as nonalloy steel, cold-reduced in coils, annealed within the 0.5-1 mm thickness band. Suited for electrical enclosures and light stampings.
CS Type B Annealed Cold-Rolled Coil 0.75mm x 914mm
Commercial steel Type B cold-rolled coil, box annealed, 0.75 mm x 914 mm width, not clad/plated, in coils. Meets HTS 7209.17.00.70 criteria as nonalloy, cold-rolled, annealed 'other' product 0.5-1 mm thick, >600 mm wide. Used for HVAC ductwork and lockers.