High-Strength Steel Coil for Structural Appliances
Cold-rolled nonalloy steel coil, 0.9 mm thick, 900 mm wide, high-strength with 380 MPa yield point, for refrigerator and washer chassis components. Fits HTS 7209.17.00.60 as cold-rolled high-strength steel in coils, 0.5-1 mm thick, not further worked. Conforms to US note (a) high-strength criteria for structural applications.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If clad with other metal
Cladding with metal constitutes 'further worked' per chapter notes, reclassifying to clad flat-rolled products.
If thickness over 1 mm
Thicker cold-rolled high-strength steel (>1 mm but ≤3 mm) falls into subsequent thickness subheadings.
If imported as tubular products
If formed into tubes/pipes before import, classification shifts to Chapter 73 articles of iron/steel.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Provide chemical composition and mechanical test reports confirming nonalloy status and high-strength properties
• Coils must be verified as 'not further worked' - no coatings or chemical treatments allowed under this code
• Watch for rust/discoloration; no duty allowance per chapter note even if occurring pre-entry
Related Products under HTS 7209.17.00.60
Cold-Rolled High-Strength Steel for Furniture Frames
0.85 mm x 700 mm wide high-strength cold-rolled steel coil, 345 MPa yield, for commercial office furniture structural frames. HTS 7209.17.00.60 applies to this cold-rolled nonalloy high-strength steel in coils, 0.5-1 mm thickness range, not further worked. Conforms exactly to chapter note strength definition.
High-Strength Cold-Rolled Steel Coil for Automotive Panels
Cold-rolled high-strength steel coil, 0.7 mm thick and 1,200 mm wide, with minimum yield strength of 355 MPa, used for outer body panels in vehicles. Classified under HTS 7209.17.00.60 as flat-rolled nonalloy high-strength steel in coils, cold-rolled, thickness 0.5-1 mm, not further worked. Meets chapter note (a) definition for high-strength steel over 3 mm thickness equivalent strength.
Automotive High-Strength Cold-Reduced Steel for Door Frames
0.6 mm thick cold-reduced high-strength steel coil, 1,500 mm wide, yield strength 275 MPa minimum, for car door inner frames. HTS 7209.17.00.60 applies to cold-rolled nonalloy high-strength steel coils 0.5-1 mm thick, width ≥600 mm, other than specific exclusions. Meets precise high-strength steel definition in US note (a).
High-Strength Steel Coil for Heavy Equipment Cabinets
Cold-rolled high-strength steel coil 0.8 mm x 1,000 mm wide, 400 MPa yield strength, for tractor and excavator control cabinets. Under HTS 7209.17.00.60 as other high-strength nonalloy steel, cold-rolled in coils, specified thickness range, not clad/plated/coated. Verified against chapter note (a) strength minimums.
Cold-Rolled High-Strength Steel for Solar Panel Frames
0.75 mm thick, 800 mm wide high-strength cold-rolled steel coil with 355 MPa yield, for renewable energy panel mounting frames. HTS 7209.17.00.60 covers this nonalloy flat-rolled product in coils, cold-rolled, high-strength steel 0.5-1 mm thick, other category. Precise fit to US note high-strength specifications.
High-Strength Steel Coil for Agricultural Machinery
Cold-rolled 0.55 mm thick high-strength steel coil, 950 mm wide, 360 MPa yield strength for combine harvester hoods. Fits HTS 7209.17.00.60 specification for nonalloy high-strength cold-rolled coils 0.5-1 mm, width over 600 mm, other category. Meets US note (a) precise strength criteria.