Cold-Rolled Nonalloy Steel for HVAC Ducting
2.2 mm thick, 1000 mm wide cold-rolled steel coil for heating/ventilation duct fabrication. Under HTS 7209.16.00.91 for cold-rolled coils not further worked, nonalloy, thickness 1-3 mm, width exceeding 600 mm, 'other' specification. Excludes specialized steels like razor blade or tool steel.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If further worked than cold-rolled (e.g., burnished)
Any listed surface treatment like burnishing moves to 7211 per chapter note on 'further worked'.
If high-strength steel specs met
High-strength steel (yield ≥275 MPa for <3mm) has dedicated subheading per U.S. note (a).
If cold-rolled but not in coils
Form factor (coil vs non-coil) splits between 7209 coils and 7210 sheets/plates.
Not sure which classification is right?
The Tariff Assistant works through the GRI rules on your specific product to reach the right HTS code — and can price the duty on it in the same conversation.
Import Tips & Compliance
• Submit heat analysis reports confirming no alloy elements meet U.S. note thresholds (e.g
• no excess chromium)
• Inspect for any chemical treatments (phosphatizing per notes) that would reclassify as further worked
• Track Section 232 tariffs separately, as they apply additionally to HTS Chapter 72 steel
Related Products under HTS 7209.16.00.91
Cold-Rolled Nonalloy Steel Coil for Automotive Panels
Flat-rolled nonalloy steel coil, cold-rolled to a thickness of 1.5 mm and width over 600 mm, used for manufacturing car body panels. It falls under HTS 7209.16.00.91 as cold-rolled, not further worked, in coils, thickness between 1-3 mm, and not meeting high-strength steel criteria. This classification applies to standard nonalloy steel products without alloying elements exceeding defined thresholds.
Cold-Rolled Steel Coil for Household Appliance Casings
Cold-rolled nonalloy steel coil, 2 mm thick and 800 mm wide, designed for refrigerator and washer outer casings. Classified under HTS 7209.16.00.91 due to its cold-rolled state in coils, thickness 1-3 mm, width ≥600 mm, and absence of cladding, plating, or alloy specifications. Meets 'other' category as standard commercial grade.
Commercial Cold-Rolled Steel Coil for Furniture Frames
1.8 mm thick cold-rolled nonalloy steel coil, width 650 mm, for metal furniture framing. Fits HTS 7209.16.00.91 as flat-rolled, coil form, cold-reduced without further working, specific thickness range, and nonalloy per U.S. note definitions. Standard grade without high-strength yield points.
Standard Cold-Rolled Steel Coil for Shelving
1.2 mm cold-rolled nonalloy steel coil, 700 mm wide, for retail shelving units. Classified in HTS 7209.16.00.91 as 'other' cold-rolled coil products of iron/nonalloy steel, thickness >1<3 mm, not clad/plated/coated, without further working. Common commercial grade.
Cold-Rolled Steel Coil for Metal Roofing
2.5 mm thick cold-rolled nonalloy steel coil, 900 mm wide, base material for corrugated roofing sheets. HTS 7209.16.00.91 applies to this uncoated, unclad, cold-rolled coil of specified dimensions without further working or special steel properties. Standard construction grade.
Industrial Cold-Rolled Nonalloy Steel Coil
1.6 mm x 750 mm cold-rolled steel coil for general industrial fabrication. Falls under HTS 7209.16.00.91 as other cold-rolled, non-further-worked coils of nonalloy steel in the 1-3 mm thickness range and ≥600 mm width. Excludes defined specialty steels.