Nonalloy Steel Hot Band Coil 2.2mm for Pipe Production
Hot band (directly from hot-rolling mill) nonalloy steel coil, 2.2 mm thick, 900 mm wide, unclad/uncoated, for welded pipe manufacturing. Fits 7208.39.00 as other hot-rolled flat products <3mm thick in coils per Chapter 72 definitions.
Import Duty Rates by Country of Origin
More Specific Codes
This product may fall under a more specific subheading:
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If already formed into welded pipes/tubes
Finished tubes/pipes classify under Chapter 73 heading 7306, not semi-finished 7208.
If alloy steel (e.g., high-strength per note a)
Alloy compositions exclude from nonalloy 7208, going to 7225 for alloy flat-rolled products.
If width <600 mm
Narrower hot-rolled coils fall to 7208.41, outside the 600mm+ width requirement.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Hot band often has scale; ensure entry docs specify not further worked beyond hot-rolling
• Cross-check thickness with caliper measurements; border-line cases get scrutinized
• Beware Section 232 tariffs may apply additionally to base MFN duties
Related Products under HTS 7208.39.00
HRPO Steel Coil 1.8mm Thick for Appliance Manufacturing
Hot-rolled pickle and oiled (HRPO) nonalloy steel coil, 1.8 mm thick, over 600 mm wide, in coils, not clad or coated beyond oiling which doesn't constitute 'further worked' per Chapter notes. Classifies under 7208.39.00 as hot-rolled, not further worked iron/nonalloy steel flat products. Ideal for washing machine and refrigerator exteriors.
Commercial Quality Hot-Rolled Steel Coil 1.5mm Thick
Commercial grade nonalloy steel hot-rolled coil, 1.5 mm thickness, 1,500 mm wide, in coils, no plating/coating, for general fabrication. Classifies precisely under HTS 7208.39.00 for hot-rolled flat-rolled products of iron/nonalloy steel under 3 mm thick.
Drawing Quality Hot-Rolled Steel Coil 1.2mm Thick
Drawing quality (DQ) nonalloy steel hot-rolled coil for deep drawing applications, 1.2 mm thick, 800 mm wide, in coils, no coatings. Perfect fit for 7208.39.00: hot-rolled flat products <3mm, not further worked.
Hot-Rolled Nonalloy Steel Coil 2.5mm Thick for Automotive Panels
This is a flat-rolled product of nonalloy steel, hot-rolled in coils, with a thickness of 2.5 mm and width exceeding 600 mm, not further worked beyond hot-rolling, not clad, plated, or coated. It falls under HTS 7208.39.00 due to its specific dimensions and minimal processing as defined in Chapter 72 for iron or nonalloy steel products. Commonly used in automotive body panel fabrication.
Hot-Rolled Steel Coil 2.0mm for Construction Framing
Nonalloy steel hot-rolled coil, 2.0 mm thickness, width 1,200 mm, not further worked, used for light structural framing in construction. Meets HTS 7208.39.00 criteria: flat-rolled iron/nonalloy steel, <3mm thick, >=600mm wide, in coils, no cladding/coating. Provides base material for slitting into studs.
Hot-Rolled Low Carbon Steel Coil 2.75mm for HVAC Ducting
Low carbon nonalloy steel hot-rolled coil, 2.75 mm thick (under 3 mm limit), width 1,000 mm+, not further worked, for HVAC duct fabrication. HTS 7208.39.00 applies to these uncoated, unclad hot-rolled coils of specified dimensions.