Pickled Hot-Rolled Steel Coil 3.2mm
Pickled hot-rolled nonalloy steel coil, 3.2mm thickness, 1600mm width, supplied in coils without further working beyond basic hot-rolling and pickling. Classifies under HTS 7208.38.00.90 for flat-rolled iron/nonalloy steel, hot-rolled coils 3mm+ to <4.75mm thick, other specs. Ideal for automotive panels and appliances.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness under 3mm
Thinner hot-rolled coils (less than 3mm) fall under 7208.37 within the same width and form category.
If plated or coated
Any cladding, plating, or coating (even minimal) shifts to plated/coated headings like 7210.
If high-strength steel per note (a)
Qualifying high-strength steel (yield point 355MPa+ for 3mm+ thick) moves to specific 7207 provisions.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Confirm pickling does not qualify as 'further worked' per Chapter notes (chemical treatments like phosphatizing are excluded, but basic pickling often accepted as not further worked)
• Provide weight and dimension certificates; statistical suffix .90 requires detailed specs for HTS reporting
• Check for Section 232 tariffs on steel; quota or duty may apply regardless of base HTS rate
Related Products under HTS 7208.38.00.90
HRPO Hot-Rolled Steel Coil 3.5mm Thick
Hot-rolled steel coil of nonalloy steel, 3.5mm thick and 1500mm wide, in coil form without cladding, plating, or coating, and not further worked beyond hot-rolling. This falls under HTS 7208.38.00.90 as it matches flat-rolled products of iron or nonalloy steel, 600mm+ width, hot-rolled in coils, thickness 3-4.75mm, other category. Commonly used for general fabrication and stamping.
Commercial Quality HR Steel Coil 4mm
Commercial quality hot-rolled nonalloy steel coil, 4mm thick, 1250mm wide, not clad or coated, in coil form not further worked. Fits HTS 7208.38.00.90 as other hot-rolled flat products of iron/nonalloy steel, 600mm+ width, 3-4.75mm thickness. Used in construction and machinery manufacturing.
Drawing Quality Hot-Rolled Coil 3.8mm
Drawing quality (DQ) hot-rolled steel coil of nonalloy steel, 3.8mm thick, 1800mm width, in coils, hot-rolled only without further treatments. HTS 7208.38.00.90 applies to this thickness range for other flat-rolled nonalloy steel products 600mm+ wide. Suited for wire drawing and deep forming.
Structural Hot-Rolled Steel Coil 3.4mm
Hot-rolled structural quality nonalloy steel coil, 3.4mm thickness, 1400mm wide, uncoated and in coil, not further worked. Matches HTS 7208.38.00.90 for other hot-rolled flat-rolled products of iron/nonalloy steel in this spec range. Applied in beams and structural fabrication.
Automotive Grade HR Coil 3.6mm Thick
Automotive-grade hot-rolled nonalloy steel coil, 3.6mm thick, 1700mm width, in coils not clad/plated or further worked than hot-rolled. HTS 7208.38.00.90 covers this as other flat-rolled iron/nonalloy steel, 600mm+ wide, 3-4.75mm thick. Used for chassis and body components.
General Purpose Hot-Rolled Coil 4.2mm
General purpose nonalloy hot-rolled steel coil, 4.2mm thickness, 1200mm wide, supplied in coil form without coatings or further processing. Falls precisely under HTS 7208.38.00.90 for other hot-rolled flat-rolled products 3mm+ to <4.75mm thick, 600mm+ width. Versatile for pipes and tanks.