Unpickled Hot-Rolled Steel Coil 3.8mm Mill Edge
Black (unpickled) hot-rolled nonalloy steel coil with mill edges, 3.8 mm thick and 900 mm wide, for heavy fabrication. HTS 7208.38.0030 applies as it's hot-rolled, in coils, untrimmed edges, no cladding/coating, and thickness 3-4.75 mm.
Import Duty Rates by Country of Origin
Alternative Classifications
This product could be classified differently depending on its characteristics or intended use.
If thickness under 3 mm
Thinner hot-rolled coils use sequential thickness-based subheadings.
If plated or coated (e.g., galvanized)
Any nonmetallic or metallic coating moves to heading 7210 for coated/plated products.
If alloy steel composition
Alloy steels (per Chapter 72 alloy definitions) classify in Chapter 72 heading 7225 regardless of processing.
Not sure which classification is right?
Our AI classifier can analyze your specific product and recommend the correct HTS code with confidence.
Import Tips & Compliance
• Expect scale/rust on surface—Chapter 72 note denies duty allowance for pre-entry discoloration
• Confirm 'not further worked' status; pickling/oiling might qualify as chemical treatment per notes
• Mark entries clearly as 'untrimmed edges' to match statistical suffix .30
Related Products under HTS 7208.38.00.30
Hot-Rolled HRPO Steel Coil 3.5mm Thick Untrimmed Edges
This is a hot-rolled, pickled and oiled (HRPO) flat-rolled product of nonalloy steel, in coils, with a thickness of 3.5 mm and width over 600 mm, featuring untrimmed mill edges. It falls under HTS 7208.38.0030 because it is not further worked beyond hot-rolling and pickling/oiling, has untrimmed edges, and meets the specified thickness range of 3 mm or more but less than 4.75 mm.
ASTM A1011 Hot-Rolled Steel Coil 4mm Untrimmed
ASTM A1011 commercial quality hot-rolled steel coil, 4 mm thick, over 600 mm wide with untrimmed edges, suitable for general fabrication. Classified under HTS 7208.38.0030 as a nonalloy steel product in coils, hot-rolled only (no cladding, plating, or coating), in the 3-4.75 mm thickness range with mill edges intact.
Mill Edge Hot-Rolled Carbon Steel Coil 3.2mm Thick
Standard mill edge carbon steel hot-rolled coil, 3.2 mm thickness, width 1,200 mm, nonalloy composition for structural use. Fits HTS 7208.38.0030 due to untrimmed edges, hot-rolled state without further working, and precise thickness specs within Chapter 72 nonalloy steel provisions.
HR Steel Coil 3.25mm Thick ASTM A36 Untrimmed
ASTM A36 structural quality hot-rolled steel coil, 3.25 mm thick with untrimmed edges, coil width 1500 mm. Classifies to HTS 7208.38.0030 for nonalloy, hot-rolled flat-rolled products in coils, specific thickness, and mill edges.
Commercial Quality HR Coil 4.5mm Mill Edge
Commercial quality hot-rolled nonalloy steel coil, 4.5 mm thickness, untrimmed mill edges, 1000 mm wide for stamping applications. Meets HTS 7208.38.0030 criteria: hot-rolled only, coils, 3-4.75 mm thick, >600 mm wide, untrimmed.
Drawing Quality Hot-Rolled Steel Coil 3.6mm Untrimmed
Drawing quality (DQ) hot-rolled steel coil for deep drawing, 3.6 mm thick with mill untrimmed edges, nonalloy. HTS 7208.38.0030 as flat-rolled iron/nonalloy steel, hot-rolled coils, exact thickness and edge condition.