Other
Angles, shapes and sections of iron or non-alloy steel. > Angles, shapes and sections, not further worked than cold-formed or cold-finished: > Other > Other
Duty Rate (from China)
Products classified under Tariff item 7216.6
Cold-Formed Steel C-Purlin
A C-shaped structural section cold-formed from flat-rolled non-alloy steel sheet, used in metal building roof systems. It is an angle, shape or section not further worked than cold-formed, obtained from flat-rolled products, and therefore falls under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Edge Trim
J-channel edge trim cold-formed from non-alloy steel flat sheet, used for drywall finishing and protection. It is a cold-formed shape obtained from flat-rolled products, not further worked, and thus classified under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Furring Channel
Resilient furring channel cold-formed from non-alloy flat-rolled steel for sound isolation in wall and ceiling systems. It is a cold-formed section obtained from flat-rolled products, not further worked, falling under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Hat Channel
Hat-shaped (omega) channel cold-formed from flat-rolled non-alloy steel sheet, used in ceiling grid systems and stud framing. It is a cold-formed shape obtained from flat-rolled products, not further worked, and classified under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel L-Angle
Equal-leg L-shaped angle cold-finished from non-alloy steel flat-rolled coil, used in light structural framing. It is a cold-formed section obtained from flat-rolled products, not further worked, and falls under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Sigma Profile
Sigma-shaped (Σ) section cold-formed from flat-rolled non-alloy steel, used in solar panel racking systems. It is a cold-formed shape obtained from flat-rolled products, not further worked, and classified under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Stud Framing
Non-loadbearing metal stud profile cold-formed from flat-rolled non-alloy steel for interior drywall partitions. It is a cold-formed shape obtained from flat-rolled products, not further worked, and falls under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Track Section
Top and bottom track profiles cold-formed from flat-rolled non-alloy steel for metal stud walls. They are cold-formed shapes obtained from flat-rolled products, not further worked, and classified under tariff item 7216.61.00.
7216.61.00Cold-Formed Steel Z-Purlin
Z-shaped purlin produced by cold-forming flat-rolled non-alloy steel for supporting roof and wall panels in pre-engineered buildings. It is a cold-formed shape obtained from flat-rolled products, not further worked, and falls under tariff item 7216.61.00.
7216.61.00Cold-Rolled Steel Lipped Channel
Lipped C-channel section cold-formed from non-alloy steel flat-rolled products, commonly used in framing for modular construction. It is a cold-formed shape obtained from flat-rolled products, not further worked, and classified under tariff item 7216.61.00.
7216.69.00Cold-Finished Carbon Steel Unequal Angle 4x2x3/8 Inch
Cold-finished unequal leg angle bar made of non-alloy carbon steel, with legs measuring 4 inches by 2 inches and a thickness of 3/8 inch. It is not further worked beyond cold-finishing, qualifying it as an angle, shape, or section under this tariff item. Commonly used in stair stringers, brackets, and structural framing applications.
7216.69.00Cold-Finished Nonalloy Steel Angle Iron 3x3x1/4 Inch
Standard equal leg angle iron made of cold-finished non-alloy carbon steel, with legs measuring 3 inches by 3 inches and a thickness of 1/4 inch. It is a versatile structural shape used in fabrication, framing, and support applications. The product is not further worked beyond cold-finishing, fitting the scope of this tariff item.
7216.69.00Cold-Finished Nonalloy Steel Hat Channel 6x2.5x14 Gauge
Hat-shaped channel section made of cold-finished non-alloy carbon steel, measuring 6 inches in depth, 2.5 inches in width, and 14 gauge in thickness. It is a cold-formed section used in drywall framing and ceiling grid systems. The product is not further worked beyond cold-finishing, qualifying under this tariff item for other cold-formed shapes.
7216.69.00Cold-Finished Nonalloy Steel U-Channel 4x2x3/16 Inch
U-shaped channel section made of cold-finished non-alloy carbon steel, measuring 4 inches deep, 2 inches wide, and 3/16 inch thick. It is a cold-formed shape used in various structural and framing applications. The product is not further worked beyond cold-finishing, fitting the definition of other cold-formed sections under this tariff item.
7216.69.00Cold-Finished Steel Slotted Angle 1x1x1/16 Inch
Pre-slotted equal angle made of cold-finished non-alloy carbon steel, with legs measuring 1 inch by 1 inch and a thickness of 1/16 inch. The slots are minimal and do not constitute further working beyond cold-finishing, so it remains classified as an angle under this tariff item. It is commonly used in retail racking and shelving systems.
7216.69.00Cold-Formed Carbon Steel L-Angle 2x2x1/4 Inch
L-shaped angle bar made of non-alloy carbon steel, with legs measuring 2 inches by 2 inches and a thickness of 1/4 inch, produced via cold-forming. It is not further worked beyond cold-forming, qualifying as an angle under this tariff item. Used in light structural framing and support applications.
7216.69.00Cold-Formed Carbon Steel Z-Purlin 8 Inch
Z-shaped purlin profile made of cold-formed non-alloy carbon steel, with an 8-inch depth, used for roofing and wall support systems in metal buildings. It is a cold-formed shape not further worked beyond cold-forming, fitting the scope of this tariff item. Provides superior load distribution in construction applications.
7216.69.00Cold-Formed Nonalloy Steel Furring Channel 7/8 Inch
Hat-shaped furring channel made of cold-formed non-alloy carbon steel, with a 7/8-inch depth, used for wall leveling in drywall applications. It is a cold-formed section not further worked beyond cold-forming, qualifying under this tariff item. Standard in construction for creating a flat surface for drywall installation.
7216.69.00Cold-Formed Steel C-Purlin 10 Inch Depth
C-shaped purlin with a 10-inch depth, cold-formed from non-alloy carbon steel for structural roof support in pre-engineered metal buildings. It is a cold-formed shape not further worked beyond cold-forming, fitting the scope of this tariff item. Essential for providing structural integrity in roofing systems.
7216.69.00Cold-Formed Steel Lip Channel 3x1.25x12 Gauge
Lipped C-channel profile made of cold-formed non-alloy carbon steel, with a 3-inch height, 1.25-inch lip, and 12-gauge thickness. It is a cold-formed section used in stud framing for commercial construction. The product is not further worked beyond cold-forming, qualifying under this tariff item for other cold-formed sections.
7216.69.00Cold-Formed Steel Super-Strut Channel 1-5/8x1-5/8 Inch
Super-Strut style channel with a 1-5/8 inch square profile, cold-formed from non-alloy carbon steel for pipe and electrical supports. It is a cold-formed shape not further worked beyond cold-forming, fitting this tariff item. Industrial support standard for mounting and framing applications.
7216.69.00Cold-Rolled Carbon Steel J-Section 4 Inch
J-shaped section made of cold-rolled non-alloy carbon steel, with a 4-inch height, used for jamb and trim applications in door and window framing. It is a cold-formed shape not further worked beyond cold-rolling, fitting this tariff item. Provides structural support and finishing in construction.
7216.69.00Cold-Rolled Nonalloy Steel Equal Leg Angle 1.5x1.5x1/8 Inch
Equal leg L-angle made of cold-rolled non-alloy carbon steel, with legs measuring 1.5 inches by 1.5 inches and a thickness of 1/8 inch. It is a cold-formed angle not further worked beyond cold-rolling, qualifying under this tariff item. Used in light framing and racking systems.
7216.69.00Cold-Rolled Steel Omega Profile 2 Inch
Omega-shaped (Ω) profile made of cold-rolled non-alloy carbon steel, with a 2-inch width, used for ceiling suspension systems in commercial interiors. It is a cold-formed shape not further worked beyond cold-rolling, fitting this tariff item. Provides grid support in suspended ceiling installations.
7216.69.00Cold-Rolled Steel T-Section 3x3x5/16 Inch
T-shaped structural section made of cold-rolled non-alloy carbon steel, with a 3-inch flange, 3-inch height, and 5/16-inch web thickness. It is a cold-formed shape not further worked beyond cold-rolling, fitting this tariff item. Ideal for beam support and structural applications.